Search results
3101
[Page extract]
ASTM D3469
These test methods measure the downward forces during the disengagement of lug-style caps from their respective containers. The methods measure the maximum torque developed while the cap is further disengaged by turning of the container.
3102
[Page extract]
ASTM D3810
This test method covers the determination of or the recommendation for minimum application torque that results in a fully degraded removal torque that is at a level greater than the maximum expected reverse-ratchet torque for a Type IA child-resistant c
3103
[Page extract]
ASTM D3968
This test method covers the measurement of rotational torques of Type IIIA child-resistant closures as a means of monitoring normal functioning of the child-resistant package.
3104
[Page extract]
ASTM D3472
This test method covers the measurement of the torque developed when Type IA child-resistant closures are rotated in the counter-clockwise direction.
3105
[Page extract]
ASTM D3470
This test method covers the determination of the force required to cause a downward-force-while-turning lug-finish closure to be rotated across the container finish lugs (strippage) without downward force being applied to the closure (Type IIA closures)
3106
[Page extract]
ASTM D3481
This test method covers the measurement of the force required to separate (or “shell”) the snap-fitted outer cap from the inner cap of Type IA, IB, or IC child-resistant closures.
3107
[Page extract]
ASTM D3787
This test method describes the measurement for bursting strength with a ball burst strength tester of textiles or garments that exhibit a high degree of ultimate elongation.
3108
[Page extract]
ASTM D1321
This test method covers the empirical estimation of the consistency of waxes derived from petroleum by measurement of the extent of penetration of a standard needle.
3109
[Page extract]
ASTM B913
This test method establishes the requirements for a standardized method of evaluating the quality of crimped-type electrical connections to solid or stranded conductors.
3111
[Page extract]
ASTM D1623
ASTM D1623 determines the tensile and tensile adhesion properties of rigid cellular plastics materials and foam. These are often used as insulation and structural materials in the aerospace, automotive and construction industries.
3112
[Page extract]
ASTM D2095
This test method covers the determination of the relative tensile strength of adhesives by the use of bar- and rod-shaped butt-joined specimens under defined conditions of preparation, conditioning, and testing.
3113
[Page extract]
ASTM D3574
ASTM D3574 is a test method used for testing soft polyurethane foam used in car seats, mattresses, pillows and other foam products. Samples come in a variety of forms including slab, bonded, and molded flexible cellular urethane foams.
3114
[Page extract]
ASTM D3658
This test method covers the simplistic comparison of strengths of glass/metal joints when the adhesive is cured by ultraviolet (UV) radiation and standard specimens are used and tested under specified conditions of preparation, radiation, and load.
3115
[Page extract]
ASTM C403/C403M
This test method covers the determination of the time of setting of concrete, with slump greater than zero, by means of penetration resistance measurements on mortar sieved from the concrete mixture.
3116
[Page extract]
ASTM D3032
These test methods detail the standard procedures for testing hookup wire insulations including all components of the insulation system used on single insulated conductors or an assembly of single insulated conductors such as a cable bundle and harness
3118
[Page extract]
ASTM D2646
These test methods may be used for acceptance testing of commercial shipments; however, caution is advised because information about between interlaboratory precision is incomplete. Comparative tests as directed in 5.1.1 may be advisable.
3119
[Page extract]
ASTM D1578
Significance and Use
Test Method D1578 for testing any spun yarn for breaking strength is considered satisfactory for acceptance testing of commercial shipments since the method has been used extensively in the trade.
3121
[Page extract]
IPC TM-650
A suite of test methods for printed circuit boards. Visual, dimensional, chemical, mechanical, electrical, environmental. To determine the release strength of the carrier of thin copper foil in pounds per inch of width at ambient temperature
3122
[Page extract]
ASTM D3106
This test method covers the determination of the permanent deformation of bare, continuous elastomeric monofilaments and filament yarns made from rubber, spandex, anidex, or other elastomers subjected to prolonged periods of tension.
3123
[Page extract]
ASTM B571
This practice covers simple, qualitative tests for evaluating the adhesion of metallic coatings on various substances.
3124
[Page extract]
ASTM B533
The force required to separate a metallic coating from its plastic substrate is determined by the interaction of several factors: the generic type and quality of the plastic molding compound, the molding process, the process used to prepare the substrat
3125
[Page extract]
ASTM D1683
This test method measures the sewn seam strength in woven fabrics by applying a force perpendicular to the sewn seams.