Search results
926
Case study
Integrità della bustina di tè
Esempio di ingegneria personalizzato Alcune delle applicazioni più semplici potrebbero non sembrare così ovvie quando le affronti. Una stringa e una linguetta su una bustina di tè?
927
[Page extract]
ASTM D6484 / D6484M - 14
ASTM D6484 is a test method that determines the open-hole compressive strength of multidirectional polymer matrix composite laminates reinforced by high-modulus fibers.
928
Case study
Adhesive bond strength of construction panels
Requirement
SIPS Frames UK Ltd (SIPS Eco Panels) is one of the UK’s leading independent Structural Insulated Panel System manufacturers, for use in the construction of kit houses by self builders.
929
[Page extract]
ISO 37
ISO 37 specifies a method for the determination of the tensile stress-strain properties of vulcanized and thermoplastic rubbers.
This test standard is equivalent to BS ISO 37.
931
[Page extract]
ASTM D952-15
ASTM D952 is a test method that covers the determination of the bond strength or ply adhesion strength of sheet plastic and electrical insulating materials.
932
Case study
Train sliding door slam force tester
Requirement
A portable device was specified for testing the force required to activate the inbuilt safety device when automatic doors close on trains.
933
Case study
Medical pouch heat seal joint tensile test
Requirement
Rocket Medical PLC are award winning designers and manufacturers of medical devices for a wide range of clinical applications.
934
[Page extract]
ASTM D3044
This test method covers determination of the shear modulus of wood-based structural panels associated with shear distortion in the plane of the panels. The method is applicable to all types of wood-based structural panels.
935
[Page extract]
IEC 61210
IEC 61210:2010 applies to non-insulated flat quick-connect terminations consisting of a male tab of size 2,8 mm, 4,8 mm, 6,3 mm or 9,5 mm with hole or dimple detents and a mating female connector for use as either an incorporated or an integrated part o
936
Case study
Cap removal test of plastic vial
Requirement
The customer approached Mecmesin with a specification to pull-off the cap of a pharmaceutical phial. The test equipment needed to be simple to use and able to perform repeatable tests.
937
Case study
Engine fuel pump spring characteristics measurement
Requirement
One of the largest automotive parts manufacturers in the Czech Republic, part of a major group, required a number of its component parts tested under high loads.
938
Case study
Page pull strength test
Requirement
Mecmesin collaborated with a customer to design and develop a force measurement system to determine book binding adhesive strength in retaining individual pages.
939
Case study
Tensile testing wire joining systems
Requirement
Gripple design and manufacture wire joiners and tensioners used extensively in the Building Services, Agriculture, Civil Engineering, Viticulture and Seismic Construction sectors.
940
[Page extract]
Motorised torque test stands
Repeatable torque testing
Looking for a motorised torque testing system to improve the accuracy and repeatability of your measurements compared to manual torque testers?
941
Case study
Wire rope termination crimp safety
Requirement
TECNI Ltd., manufactures and supplies a range of steel, braided and wire rope assemblies for applications as diverse as security locks, balustrades, marine rigging, winching systems and gym equipment.
942
[Page extract]
BS EN ISO 19011:2011
Provides the fundamental knowledge needed for auditing management systems and has been expanded to reflect modern thinking and the intricacies of auditing multiple management system standards (MSS).
943
[Page extract]
Real-world applications
Plastic bottles and closures
In beverage and household product manufacturing, top-load testing is essential to confirm that bo
944
Event
Essentials of Grip & Fixture Selection Pt. 2
The accuracy of instrument itself- though important, is only one piece of the measurement accuracy puzzle. Grip and fixture selection plays a critical role in the applications in Force and Materials quality testing.
945
Case study
Luer lock fastening and release torque
Customised engineering example
Luer lock test standards frequently call for measuring torque whilst simultaneously applying a pre-defined axial force.
946
[Page extract]
ISO 7622-1
ISO 7622-1 specifies a method for the determination of the elongation of steel cords constituting the carcass of conveyor belts, when subjected to a force corresponding to 10 % and 60 % of the specified tensile strength.
947
[Page extract]
TAPPI T 804
This method is used for measuring the ability of corrugated or solid fiber shipping containers to resist external compressive forces.
948
[Page extract]
ASTM D2979
This test method covers measurement of the pressure-sensitive tack of adhesives.
950
[Page extract]
Applications of needle penetration testing
Medical devices
Used to confirm that components such as vial stoppers, syringe seals, and gloves can resist penetration by needles while maintaining their intended function.