Search results
1702
Event
Essentials of GRIP & FIXTURE Selection in Force & Torque Testing Webinar
When physically testing a material or component, the ability to apply load to a test specimen is important—but having the ability to apply that load correctly is just as crucial.
1703
[Page extract]
ASTM D6109-19
ASTM D 6109 determines the flexural properties for any solid or hollow manufactured plastic lumber product of square, rectangular, round, or other geometric cross section that shows viscoelastic behavior.
1704
[Page extract]
BS EN 60794-1-21:2015+A1
This part of IEC 60794 applies to optical fibre cables for use with telecommunication equipment and devices employing similar techniques, and to cables having a combination of both optical fibres and electrical conductors.
1706
[Page extract]
ISBT PTC-00019
This document provides a collection of test methods for the qualification of plastic flat-top closures applied on PET bottles that are used in the beverage industry.
1707
[Page extract]
BS EN 5057
Specifies requirements for dimensions, performance characteristics and test programme. section 16 is insertion & withdrawal force test
1708
[Page extract]
ISO 7886-2
This document specifies requirements for sterile single-use hypodermic syringes of nominal capacity 1 ml and above, made of plastic materials and intended for use with power-driven syringe pumps. Annexe B covers the Pump Force to be measured.
1709
[Page extract]
ISO 5628
Specifies three test methods for determining the bending stiffness of paper and paperboard. The test methods differ in the type of loading mode, thus giving rise to the two-point, three-point and four-point bending test methods.
1710
Case study
Prova di resistenza alla trazione della cinghia per mobili
Requisiti Supportato dalla Royal Household del Castello di Windsor, uno studente della Buckinghamshire New University stava studiando le proprietà di usura e resistenza delle tradizionali cinghie inglesi a base di iuta, utilizzate nella costr
1711
Event
Cork Pull & Cork Compression Testing OnDemand Webinar
FORCE TESTING in Wine & Spirit Applications
1712
[Page extract]
Government
The general government sector covers institutions and public bodies where regulations and standards must be strictly adhered to.
1713
[Page extract]
Comparative analysis with other peel tests
Test type
Peel angle
Common applications
Advantages
1714
[Page extract]
Common challenges and solutions
Misalignment can cause uneven peeling forces.
1715
[Page extract]
Understanding test types
Material testing uses a variety of methods to assess different mechanical properties. Selecting the right test depends on the intended application and relevant standards.
Examples include:
1716
[Page extract]
What is wing tear testing (Winkelmann/Graves method)?
Wing tear testing is a tensile-based method for flexible materials, in which a wing-shaped specimen is subjected to a controlled force until it tears.
1717
[Page extract]
Differences and similarities to other corrugated tests
While TAPPI T 824 focuses on the intrinsic crush strength of pre-fluted medium, other common corrugated tests measure different performance factors:
1718
[Page extract]
Why Mecmesin?
With over 40 years of experience, Mecmesin delivers torque testing systems that are precise, easy to use, and fully supported.
1719
[Page extract]
Introduction to double rip tongue tear testing
Double rip tongue tear testing is a recognised method for assessing the tear resistance of flexible materials including co
1720
[Page extract]
Loop tack test procedure
Sample preparation
Cut adhesive strips to the required length and width stated in the chosen standard. Condition the samples at the specified temperature and humidity before testing.
1721
[Page extract]
Burst testing techniques and equipment
Compressive burst testing
In compressive burst testing, force is applied through a hemispherical probe until the material ruptures.
1722
[Page extract]
Speak to an expert
Tensile testing and elongation at break measurement are essential for material performance evaluation, product development, and quality assurance.
1723
[Page extract]
Why is the 135° peel test important?
Seal strength testing plays a vital role in packaging quality control.
1724
[Page extract]
Introduction to equibiaxial flexure compression testing
Equibiaxial flexure compression testing is a materials testing method used to evaluate a specimen’s resistance to bending under multi-directional loading.
1725
[Page extract]
Why is the trapezoidal tear test important?
Tear resistance is a critical measure of a material’s durability, particularly in applications where the material may be subject to punctures, cuts, or repeated stress.