Search results
2277
[Page extract]
ASTM D6415 / D6415M-06a
ASTM D6415 is designed to measure the curved beam strength properties of fiber reinforced composites using a 90˚ curved beam specimen. The curved beam strength represents the moment per unit width which causes a delamination to form.
2278
[Page extract]
ISO 13954
ISO 13954 describes a peel test method for determining the decohesive resistance of polyethylene electrofusion socket assemblies for use in the distribution of fluids.
2279
[Page extract]
ASTM D412-16
ASTM D412 is a test standard for testing the tensile stress-strain properties of thermoset rubbers and thermoplastic elastomers. The standard is divided into two test methods.
2280
[Page extract]
ASTM F2606-08
This guide can be used to obtain force versus deflection or midspan bending moment versus midspan curvature curves for stents and stent systems subjected to three-point bending conditions.
2281
[Page extract]
ASTM C165
1.1 This test method covers two procedures for determining the compressive resistance of thermal insulations.
2282
[Page extract]
ASTM D 2979
1.1 This test method covers measurement of the pressure sensitive tack of adhesives.
2283
[Page extract]
TAPPI T 400
This method describes procedures for obtaining a representative sample for testing.
2284
[Page extract]
TAPPI T 840
This method describes a procedure for evaluating the adhesive used in glued lap joints of corrugated containers.
2285
[Page extract]
ASTM D380
ASTM D380 is a set of test methods for determining testing and inspection procedures for rubber hoses e.g. hydraulic hoses and automotive hoses.
2286
Event
Essentials of Consumer Packaging Testing
Maximize COST SAVINGS for your consumer packaging by minimizing excess material and “over design” while keeping your products protected in transit.
2287
[Page extract]
BS EN ISO 8295
ISO 8295 specifies a method for determining the coefficients of starting and sliding friction of plastics film and sheeting when sliding over the same or other substances. It is intended to be used for non-sticky plastic film and sheeting of up to appr
2288
[Page extract]
ASTM D3164
Test method ASTM D3164 is used to produce shear strength data for joints to compare adhesives or evaluation surface treatments. Shear joints impose uniform stresses across the bond area which results in the highest possible joint strength.
2290
Sensor
Capteurs - pour bancs d'essai universel de matériaux
Capteurs
Les systèmes d'essai de matériaux OmniTest et MultiTest-dV utilisent la gamme de capteurs de charge améliorée (ELS) haute précision de Mecmesin pour enregistrer les charges de traction et de compression.
ELS
Un capteur de charge de…
2291
[Page extract]
Energy
Mecmesin has long been providing force and torque testing solutions to suppliers and contractors into the energy industry...
2292
[Page extract]
Construction
Mecmesin systems and gauges are designed for the application of international and industry standards for quality and safety...
2293
[Page extract]
Bijouterie et Horlogerie
Dans la fabrication de bijoux et de montres, les alliages, composants et autres matériaux doivent répondre aux besoins du processus de fabrication et le produit final doit offrir de bonnes performances de service lorsqu'il est porté par le client.
2294
Sensor
Capteurs - MultiTest-dV
Capteurs de force
Le MultiTest-dV est un banc d'essai extrêmement flexible, qui peut être configuré avec un dynamomètre pour tester les produits semi-finis et finis ou un capteur de charge amélioré pour les tests de matériaux.
AFG
Un…
2295
Sensor
Sensors - Vortex-dV
Torque sensors
A range of 'Smart' interchangeable torque sensors are specially adapted for the Vortex-dV test system. Plug and play for automatic calibration and a range of capacities for all requirements, from 1.5 N.m (13 lbf.in) to 10 N.m (90 lbf.in).…
2296
[Page extract]
Architecture
Les tests de force et de couple dans le secteur de l’architecture consistent principalement à tester le matériel architectural et les systèmes de contrôle d’accès, afin de s’assurer que les forces opérationnelles sont conformes aux limites définies par
2299
[Page extract]
Rouleau flottant
Letest de pelage au rouleau flottant est une méthode critique utilisée pou
2300
[Page extract]
Elongation and Recovery
Elongation and recovery testing is a fundamental process in material science used to measure how far a material can stretch under a given load and how effectively it returns to its original shape once the force is removed.