Search results
1501
[Page extract]
IEC 60598
IEC 60598-1 specifies general requirements for luminaires, incorporating electric light sources for operation from supply voltages up to 1 000 V.
1502
[Page extract]
ASTM D5934-02
ASTM D5934 specifies the use of controlled rate of loading mechanical instrumentation on rectangular plastic bars molded directly or cut from sheets, plates, or molded shapes via three-point loading bending techniques to obtain material properties such
1503
[Page extract]
ISO 594-1
Specification of the requirements for conical (Luer) fittings for use with hyperdemic syringes and needles and with certain other apparatus for medical use such as transfusion and infusion sets.
1504
[Page extract]
ASTM F1551-09
References a wide range of methods for tensile strength, peel, pull-out, abrasion resistance and other physical properties, as suitable for synthtic playing surfaces.
1505
[Page extract]
ASTM F36-15
The ASTM F36 test method covers the determination of the short-time compressibility and recovery at room temperature of sheet-gasket materials, form-in-place gaskets, and in certain cases, gaskets cut from sheets.
1506
[Page extract]
ASTM D6742 / D6742M
ASTM D6742 is the standard test method for tensile and compression testing of filled-hole polymer matrix composite laminates. It provides instructions for modifying open-hole tension and compression test methods to determine filled-hole tensile and com
1507
Event
Essentials of Adhesion (Peel) Testing
There is a reason people reach for Duct Tape as a fix for almost everything – Adhesion Strength. From busted pipes to ripped furniture, the preference for a solution that “does not easily peel off” is the guiding principle for manufactures.
1508
[Page extract]
UL 486A-B
UL 486A-B is a safety standard that outlines the requirements for wire connectors and soldering lugs used with electrical conductors.
1509
[Page extract]
ISO 178
ISO 178 is a test method for the determination of flexural properties of rigid and semi-rigid plastics. These properties include flexural modulus and flexural strength.
1510
[Page extract]
ASTM F2824-10
1.1 This test method describes a method for the measurement of mechanical seal strength while separating the entire lid (cover/membrane) from a rigid or semi-rigid round container. 1.2 This test method differs from Test Method F88.
1511
[Page extract]
ASTM D937-97
1.1 This test method covers measuring with a penetrometer the penetration of petrolatum as an empirical measure of consistency.
1512
[Page extract]
PSTC 101
These methods cover the measurement of the peel adhesion of pressure sensitive tapes.
1513
[Page extract]
BS 6079-1
BS 6079-1 aims to help people and organizations achieve a desired outcome of a project efficiently and effectively, as well as to contribute to the learning within projects and so continually improve their organization’s project management capability.
1515
[Page extract]
ASTM D5868-01
Due to the increased use of adhesively-bonded FRP as a result of the inherent advantages afforded by bonded rather than mechanically-fastened joints (particularly the alleviation of stress risers and stress cracking), there is a need for tests by which
1516
[Page extract]
MIL 22520-G
This specification covers the general requirements for crimping tools, accessories and inspection gages used for connecting removable contacts (such as; signal, power, coaxial, shielded, thermocouple, and filter pin contacts) coaxial connectors, shielde
1517
[Page extract]
BS EN ISO 527-2
ISO 527-2 specifies the test conditions for determining the tensile properties of moulding and extrusion plastics, based upon the general principles given in ISO 527-1.
1518
[Page extract]
ISO 37
ISO 37 specifies a method for the determination of the tensile stress-strain properties of vulcanized and thermoplastic rubbers.
This test standard is equivalent to BS ISO 37.
1519
[Page extract]
BS EN 868-5
Provides examples of particular requirements and test methods for heat and self-sealable pouches and reels manufactured from paper complying with EN 868-3 and plastic film complying with clause 4 of this European standard.
1520
[Page extract]
ASTM D885/D885M-10a
These [comprehensive] test methods cover the testing of industrial filament yarns made wholly of manufactured organic-base fibers, cords twisted from such yarns, fabrics woven from such cords, and products that are made specifically for use in the manuf
1521
[Page extract]
ASTM D2718
These test methods determine the shear properties of structural panels associated with shear distortion of the planes parallel to the edge planes of the panels. Both shear strength and modulus of rigidity may be determined.
1522
[Page extract]
SAE USCAR-21-4
This specification defines test methods and requirements for validation of solderless crimped connections.
1523
Event
Compression Testing in Automotive Applications
From R&D to the shop floor, Compression Testing plays a key role in Automotive Manufacturing to meet strict quality controls and ensure consumer safety and product longevity.
1524
[Page extract]
USP <671>
Chapter 671 of USP (United States Pharmacopeia) provides standards for the functional properties of packaging systems used for solid oral dosage forms (SODF) and liquid oral dosage forms (LODF) for pharmaceuticals and dietary supplements.