Search results
476
Event
Materials Testing: Theory and Practice Pt. 1 & 2
Materials testing is often the last step in the manufacturing process. Yet, quality is the result of both the process and the material. If the material that goes into the product is inadequate or defective, then the product may be deficient or faulty.
477
[Page extract]
DIN EN 1464
This European Standard specifies a floating roller method for the determination of the peel resistance of high-strength adhesive bonds between one rigid adherend and one flexible adherend when tested under specified conditions of preparation and testing
478
Case study
Needle to ferrule pull-out test
Requirement
The customer, Oxford Instruments, wished to perform a destructive pull-out test to evaluate the maximum tension force to pull the 2 components apart.
479
Event
Tensile Testing for Wiring Harness Connections
The only way of really knowing the strength of a crimped terminal is to pull it. This can reveal production problems, where strand nicks, incorrect crimp height, or effects from changes in terminal supply, may not be clearly apparent.
480
Event
Tensile Testing for Wiring Harness Connections
The only way of really knowing the strength of a crimped terminal is to pull it. This can reveal production problems, where strand nicks, incorrect crimp height, or effects from changes in terminal supply, may not be clearly apparent.
481
Event
T-Peel (Adhesion Strength) Testing
This webinar will focus on the most common approach to measuring the adhesion strength of two materials bonded together with an adherent.
482
Case study
Removal torque of 'squeeze and twist' child-resistant cap
Requirement
Reckitt-Benckiser are manufacturers of the distinctive HDPE (High Density Polyethylene) swan-neck 'Harpic' cleaning fluid bottles.
483
[Page extract]
Standards and guidelines
Accurate and comparable cleavage strength testing depends on following recognised international standards.
484
Page
Accessory catalogue
Choosing your accessories
To achieve accurate test results it's important that your sample is gripped and held correctly.
485
Event
Texture Testing for Bakery Applications
The primary goal for using instrumentation to measure texture is to capture an objective value to something that is typically evaluated very subjectively. Texture cannot be controlled unless it measured in a consistent and repeatable manner.
486
Event
Tensile Testing for Wiring Harness Connections
The only way of really knowing the strength of a crimped terminal is to pull it. This can reveal production problems, where strand nicks, incorrect crimp height, or effects from changes in terminal supply, may not be clearly apparent.
487
Event
Tensile Testing for Wiring Harness Connections
The only way of really knowing the strength of a crimped terminal is to pull it. This can reveal production problems, where strand nicks, incorrect crimp height, or effects from changes in terminal supply, may not be clearly apparent.
488
[Page extract]
ASTM D3359
These test methods cover procedures for assessing the adhesion of coating films to metallic substrates by applying and removing pressure-sensitive tape over cuts made in the film.
489
Event
Fundamentals of Texture Testing Analysis
The primary goal for using instrumentation to measure texture is to capture an objective value to something that is typically evaluated very subjectively. Texture cannot be controlled unless it measured in a consistent and repeatable manner.
490
Event
Fundamentals of Texture Testing Analysis
The primary goal for using instrumentation to measure texture is to capture an objective value to something that is typically evaluated very subjectively. Texture cannot be controlled unless it measured in a consistent and repeatable manner.
491
Event
Fundamentals of Food Texture Analysis
The primary goal for using instrumentation to measure texture is to capture an objective value to something that is typically evaluated very subjectively. Texture cannot be controlled unless it measured in a consistent and repeatable manner.
493
Event
The fundamentals of torque testing
If you have every struggled to open your favorite bottle of water or jam, or required help loosening the lug nuts on your car's wheels, it's likely due to a case of over-torque.
494
Accessory
Lightweight Lower Chuck, for use on base of Helixa stand
432-509
Lightweight Lower Chuck for Helixa
A pin-chuck fitted with an adaptor for connection to the motor spindle of 'Helixa' motorised test stands.
Max.opening 3.2mm. Supplied with T-bar to allow easy opening and tightening
Used for holding components and…
495
Accessory
Transit Case for Manual Handling/Ergonomic Kit
416-007
A foam-lined rugged metal case for the components of the advanced or basic manual handling kit. Supplied as standard with the kit, has space for: a force gauge including rechargeable batteries, mains adaptor / battery charger, gripping cradle, chain link…
496
Accessory
PSV12129 Split mandrel cork grip
PSV12129
A Split Mandrel Grip comprising an outer body with lead-screw and handles. Used for adjustable positioning of half-round jaws having wire-eroded serrated faces.
Designed specifically to grip natural corks of 26-32 mm diameter when testing the release…
497
Accessory
sample holder for standard fixture table
432-244
Fits to the standard fixture table (432-243) and used for easy configuration and alignment of test fixtures. The small-sample holder has been designed to accommodate spherical or irregular samples. Three sizes of holding plate are supplied.
498
Accessory
PSV12129 Split mandrel cork grip
PSV12129
A Split Mandrel Grip comprising an outer body with lead-screw and handles. Used for adjustable positioning of half-round jaws having wire-eroded serrated faces.
Designed specifically to grip natural corks of 26-32 mm diameter when testing the release…
499
Case study
Top-load Testing of Plant-based PLA Material Bottles
Requirement
BioPak Solutions in Roquefort-les-Pins, France, are leaders in the production of Polylactic Acid (PLA) bottles. The bottles are oil-free, contain no PET or Bisphenol A, and are made 100% from carbon-absorbing plants.
500
Case study
PCB Solder Joint Shear
Requirement
Millennnium Microtech Thailand, part of Microchip Technology Inc Thailand operates a manufacturing, packaging and testing plant for Printed Circuit Board (PCB) Integrated Circuit (IC) components.