Search results
2376
[Page extract]
ASTM E2658-15
These practices cover procedures and requirements for the calibration and verification of testing machine speed by means of standards calibration devices
2377
[Page extract]
IEC 60598
IEC 60598-1 specifies general requirements for luminaires, incorporating electric light sources for operation from supply voltages up to 1 000 V.
2378
[Page extract]
ISO 1924-2
Specifies a method for measuring the tensile strength, strain at break and tensile energy absorption of paper and board, using a testing machine operating at a constant rate of elongation (20 mm/min).
2379
[Page extract]
BS 6319-3
BS 6319-3 is a test method for determining the modulus of elasticity in flexure and flexural strength of resin and polymer/cement compositions for use in construction.
2380
[Page extract]
ASTM F543-13
This specification provides requirements for materials, finish and marking, care and handling, and the acceptable dimensions and tolerances for metallic bone screws that are implanted into bone.
2381
Event
Webinar: Rice Texture Analyzer (Thai) - เทคโนโลยีเครื่องมือวัด และมาตรฐานการทดสอบข้าว
เทคโนโลยีเครื่องมือวัด และมาตรฐานการทดสอบข้าว
หนึ่งในปัจจัยที่สําคัญที่สุด ซึ่งมีผลต่อความสำเร็จของผลิตภัณฑ์ข้าวคือ เนื้อสัมผัส
เนื้อสัมผัสของข้าวส่งผลโดยตรงต่อความพึงพอใจของผู้บริโภค และความน่าเชื่อถือของผู้ผลิตข้าว นั่นคือเหตุผลว่า
2382
[Page extract]
ASTM D5179-16
ASTM D5179 is a test method for determining organic coatings adhesion to a plastic substrate. It can be used to evaluate the adhesion (pull-off strength) of various coating/substrate combinations e.g. paint and varnish.
2383
[Page extract]
BS EN ISO 21181
BS EN ISO 21181 is a test method for determining the relaxed elastic modulus of light conveyor belts.
2384
[Page extract]
ANSI/EIA 364
Mating and Unmating Procedure for Force Testing of Electrical Connectors and Sockets
2385
[Page extract]
BS EN 13942
This International Standard specifies requirements and provides recommendations for the design, manufacturing, testing and documentation of ball, check, gate and plug valves for application in pipeline systems meeting the requirements of ISO 13623 for t
2386
[Page extract]
ASTM D953-18
ASTM D953 is a test method that covers the determination of the pin-bearing strength of rigid plastics in either sheet form, molded form, or in reinforced thermoset form.
2387
[Page extract]
BS EN 868-5
Provides examples of particular requirements and test methods for heat and self-sealable pouches and reels manufactured from paper complying with EN 868-3 and plastic film complying with clause 4 of this European standard.
2388
[Page extract]
BS EN 455-2
Protective gloves, Protective clothing, Gloves, Surgical equipment, Sterile equipment, Disposable, Medical equipment, Dimensions, Length, Width, Ageing (materials), Strength of materials, Physical properties of materials, Physical testing
2389
[Page extract]
BS EN ISO 6892-1
This part of ISO 6892 specifies the method for tensile testing of metallic materials and defines the mechanical properties which can be determined at room temperature.
2390
[Page extract]
Vice grip (Pneumatic)
Vice grips (single-action) - having one fixed jaw against which a second parallel jaw is tightened. The position of the fixed face may be adjustable to accommodate differing specimen thickness.
2391
[Page extract]
CETIE Guide 7
This guideline applies to the screw capping of still wines with a metallic closure having a threaded plastic insert and a tamper-evident band which needs to be snapped before it can be opened. The closure is screwed and crimped during capping.
2392
[Page extract]
USP <381>
This chapter applies to closures used for long-term storage of preparations defined in the general test chapter Packaging and Storage Requirements á659ñ, Injection Packaging.
2393
[Page extract]
ASTM D751-06
These test methods cover, but are not limited to, rubber-coated fabrics, that is, tarpaulins, rainwear, and similar products.
2394
[Page extract]
ASTM D6534-05
This test method covers the determination of the peak force-to-actuate, sometimes called force-to-actuate (FTA), of a mechanical pump dispenser.
2395
[Page extract]
ISO 29862
This test standard specifies a series of methods for the determination of peel adhesion properties of self adhesives tapes.
2396
[Page extract]
ISO 16047
ISO 16047:2005 specifies the conditions for carrying out torque/clamp force tests on threaded fasteners and related parts.
2397
[Page extract]
ASTM C1674
This test method covers the determination of the flexural strength (modulus of rupture in bending) at ambient conditions of advanced ceramic structures with 2-dimensional honeycomb channel architectures.
2399
[Page extract]
ASTM F904
ASTM F904 is a test method that covers a procedure for comparing the bond strength or ply adhesion of similar laminates made from flexible materials such as cellulose, paper, plastic film, and foil.
2400
[Page extract]
ASTM D3481
This test method covers the measurement of the force required to separate (or “shell”) the snap-fitted outer cap from the inner cap of Type IA, IB, or IC child-resistant closures.