Search results
2301
[Page extract]
Speak to an expert
For advice on elongation and recovery testing, or to discuss how Mecmesin’s equipment can be configured for your specific materials and applications, speak with one of our technical specialists.
2302
[Page extract]
The role of ECT in quality assurance
The Edge Crush Test is a widely used measure for predicting box stacking performance.
2303
[Page extract]
Secant modulus compared to other moduli
Different moduli are used to describe the stiffness of materials, each calculated at different points on the stress-strain curve:
2304
[Page extract]
Applications in plastics and paper packaging
Plastic film processing
Plastic films must maintain precise COF levels to feed correctly through wrapping and sealing systems.
2305
[Page extract]
Equipos de prueba
Mecmesin ofrece una gama de equipos de ensayo de fuerza adecuados para el ensayo de jeringas según la norma ISO 11040-4 Anexo F.
2306
[Page extract]
Science & Technology
Science & Technology companies often act as an interface between business and centres of knowledge such as universities, government-funded laboratories, and in some instances corporate laboratories.
2307
Caso de estudio
Luer y conector de pequeño calibre Prueba de torque
Requisito Las normas internacionales relevantes para conectores de pequeño calibre para líquidos y gases en aplicaciones de atención médica se centran en su facilidad de uso y resistencia a fugas o mal manejo.
2308
[Page extract]
*corp 01M-01-225
Determination of the Elongation, Recovery and Modulus of Elastic Fabrics.
A fabric specimen of specified dimensions is extended at a constant rate to a specified force for three cycles.
2309
[Page extract]
CETIE Guide 6
This guide gives information on good practice for bottling still wine with an aluminium screw caps on a BVS type glass finish according to EN 16293, with redraw of the cap on application.
2310
[Page extract]
ISO 15359
This International Standard specifies, a friction-testing method based on the horizontal plane principle, and the procedure for the determination of the static coefficient of friction before, and static and kinetic coefficients of friction after, a spec
2311
[Page extract]
ASTM D5618-94
This test method covers the measurement of barnacle adhesion in shear to surfaces exposed in the marine environment. It is used to establish the ability of a surface to reduce biofouling adhesion.
2312
[Page extract]
EN TS 15945
The purpose of DD CEN/TS 15945 is to specify test methods to evaluate the ease of opening of consumer packages, in order to improve easy access to the contents. For packages regulated for safety or similar reasons, e.g.
2313
[Page extract]
SAE USCAR-38
This specification defines basic test methods and requirements for ultrasonically welded cable termination type connections.
2314
[Page extract]
ASTM D3518 / D3518M
ASTM D3518 is a test method, which measure the shear stress and shear strain properties of polymer matrix composite materials composed of +45 plies and -45° plies.
2315
[Page extract]
IEC 61210
IEC 61210:2010 applies to non-insulated flat quick-connect terminations consisting of a male tab of size 2,8 mm, 4,8 mm, 6,3 mm or 9,5 mm with hole or dimple detents and a mating female connector for use as either an incorporated or an integrated part o
2316
[Page extract]
ASTM C394
This test method covers determination of the effect of repeated shear loads on sandwich core materials.
2317
[Page extract]
ASTM D4032-08
This test method covers the determination of the stiffness of fabrics by the circular bend procedure. The method is generally applicable to all types of fabrics, including woven, knitted and nonwovens, of any fiber content.
2318
[Page extract]
BS EN 17665
The Directive (EU) 2019/904 “on the reduction of the impact of certain plastic products on the environment” introduces the requirement that plastic caps and lids of single use plastic beverage containers up to 3 l capacity shall remain attached to the c
2319
[Page extract]
ISO 3781
Specifies a test method for the determination of the wet tensile strength of paper or board after its immersion in water for a specified period.
2320
[Page extract]
BS EN ISO 527-1
BS EN ISO 527-1 specifies the general principles for determining the tensile properties of plastics and plastic composites under defined conditions.
2321
[Page extract]
ISO 14126
ISO 14126 outlines procedures for determining the compressive properties of fibre-reinforced plastics composites in the in-plane direction. Two methods are detailed in the standard:
2323
[Page extract]
ASTM F1995-12
This test method covers the determination of the shear integrity of materials and procedures used to attach surface mount devices (SMD) to a membrane switch circuit.
2324
[Page extract]
*corp Ford DSEU
Test method covering measurement of door slam energy for Ford Chenai, India. Shows Mecmesin loadcell, display and special gripping fixtures. Note: Diagram shows a rigid link bar, which was later replaced by a flexible bungee connection.