Search results
451
Case study
Abrasion and micro-scratch testing of wood and laminate surfaces
Requirement
The use of natural materials has long been a unique selling point across many consumer product lines.
452
Product
Motorisierter Kraftprüfstand
MultiTest-dV
810-401
Der MultiTest-dV ist ein vielseitige und einfach zu verwendende Kraftprüfmaschine.
Ideal für die routinemäßige Qualitätskontrolle in der Produktionsstätte oder im Labor. Drei Modelle sind für 0,5 kN , 1 kN und 2,5 kN ausgelegt.
Ein…
453
Product
Manual Pull Tester
Alluris FMT-W30
PSV21019
The FMT-W30 is a manually-operated pull tester available in 2 models with a tensile strength capacity up to either 500N (110 lbf) or 1000N (220 lbf).
Compact and rugged it is specifically designed for ease of use with minimal training, and is an ideal…
454
Event
Cork Pull & Cork Compression Testing OnDemand Webinar
FORCE TESTING in Wine & Spirit Applications
455
Case study
Tensile testing wire joining systems
Requirement
Gripple design and manufacture wire joiners and tensioners used extensively in the Building Services, Agriculture, Civil Engineering, Viticulture and Seismic Construction sectors.
458
Case study
TerraFixings Einsatz des OmniTest 25 von Mecmesin für die direkte Kohlenstoffabscheidung aus der Luft
TerraFixing widmet sich der Bekämpfung des Klimawandels durch erschwingliche und skalierbare Direct Air Carbon Capture (DAC).
459
Software
VectorPro force testing software
VectorPro® software
VectorPro is our advanced force testing software package developed to perform tensile, shear, bend and compression tests on materials, components and products. Present measurement data graphically and share customised test reports…
460
[Page extract]
Applications of short span compression testing
SCT is widely applied in quality assurance, R&D, and material qualification:
461
[Page extract]
Testing methods and equipment
A cleavage strength test requires precise load application and accurate force measurement at the point of separation.
462
[Page extract]
Introduction to short span compression tests
The short span compression test (SCT) is a mechanical testing method used to measure the compressive strength of materials over a very short span.
463
[Page extract]
What is 180 degree peel testing
The 180 degree peel test is a recognised method for measuring the strength of adhesive bonds when a material is peeled back on itself at a constant angle of 180 degrees.
464
[Page extract]
Procedure for tensile testing
While the specifics vary depending on material type and applicable standards, the general procedure includes:
465
[Page extract]
The concentric ring method
The most widely used approach to equibiaxial flexure compression testing is the concentric ring method. A circular specimen is supported on an outer ring and loaded through a smaller, concentric inner ring.
466
[Page extract]
Methods for lap shear testing
Single lap shear test procedure
In a single lap shear test, two specimens are bonded with an adhesive in an overlapping configuration.
468
[Page extract]
Get help with your products
Whether you're setting up a new test system or looking for documentation on an existing one, our online Support Center is the first place to start.
469
[Page extract]
What is top-load testing?
Top-load testing, also known as column crush testing, is a method used to evaluate the ability of a packaging component to withstand a vertical compressive force without deforming or failing.
471
[Page extract]
Performing a five-point bend test
Specimen preparation
Cut specimens to the standardised dimensions specified in ASTM D2718.
Ensure surfaces are smooth and free from defects that could affect results.<
472
[Page extract]
Standard methods and procedures
T-peel testing is governed by recognised standards to ensure consistency and repeatability of results. The most common are:
473
[Page extract]
How peel wheel tests are conducted
Specimen preparation – The bonded material is cut to defined dimensions, ensuring uniformity of size and adhesive application.
474
[Page extract]
Why Mecmesin for material testing solutions
Expertise across diverse sectors
Mecmesin has decades of experience supporting industries from packaging and oral care to pha
475
[Page extract]
Yield point testing methods
Yield point testing is most often performed using tensile testing, in which a specimen is subjected to a steadily increasing axial load until plastic deformation occurs.