Search results
1926
[Page extract]
CETIE Guide 5
This document gives background information and recommended best practices for the application of plastic flat-top screw-on caps onto PET bottles for beverages. It covers all closure sizes and beverage product types.
1927
[Page extract]
ASTM D5034-09
This test method covers the grab and modified grab test procedures for determining the breaking strength and elongation of most textile fabrics. Provisions are made for wet testing.
1928
[Page extract]
ISO 20502
SO 20502:2005 describes a method of testing ceramic coatings by scratching with a diamond stylus.
1929
[Page extract]
BS EN ISO 9000
ISO 9000 gives an overview of the fundamentals and concepts around quality management.
1930
[Page extract]
ISO 8364
ISO 8364:2007 specifies requirements and test methods for the binding mounting area and free space area, ski bindings and retention devices of alpine skis, in order to optimize the compatibility of the functional unit "ski binding - retention device - b
1931
[Page extract]
BS EN 1607
This European Standard specifies the equipment and procedures for determining the tensile strength of a product perpendicular to its faces. It is applicable to thermal insulating products.
1932
[Page extract]
*corp Coca-Cola SM-PR-2645
This test ensures that the column strength of non-refillable (NR) plastic bottles is sufficient to meet minimum performance specifications for vertical loading during peak load application.
1933
Event
Fundamentals of Texture Testing Analysis
The primary goal for using instrumentation to measure texture is to capture an objective value to something that is typically evaluated very subjectively. Texture cannot be controlled unless it measured in a consistent and repeatable manner.
1934
Event
Cap Closure and Removal Torque Testing
The primary objective for measuring and analyzing the torque characteristics of a container cap is to accurately determine not only the quality of the part or process, but also the root cause of a wide variety of defects.
1935
[Page extract]
ISO 7622-1
ISO 7622-1 specifies a method for the determination of the elongation of steel cords constituting the carcass of conveyor belts, when subjected to a force corresponding to 10 % and 60 % of the specified tensile strength.
1936
Event
Fundamentals of Texture Testing Analysis
The primary goal for using instrumentation to measure texture is to capture an objective value to something that is typically evaluated very subjectively. Texture cannot be controlled unless it measured in a consistent and repeatable manner.
1937
[Page extract]
ISO 8510-1
Particularly suitable for use with less flexible adherends for which a 180 ° peel test is not suitable because the adherends crack, break or delaminate. A bonded assembly of two adherends is prepared using the adhesive under test.
1938
[Page extract]
BS 6319-7
BS 6319-7 is a test method for determining the tensile strength of resin and polymer/cement compositions for use in construction.
1939
[Page extract]
BS EN ISO 16409
Describes performance criteria for manual interdental brushes with a round cross-section of the brush head and consisting of a wired stem with inserted filaents.
Of particular interest is the Stem Retention Force (sections 5.4 and 7.6)
1941
[Page extract]
ASTM D7137 / D7137M-17
ASTM D7137 is a test method that measures the compression residual strength properties of multidirectional polymer matrix composite laminated plates, which have been subjected to quasi-static indentation
1942
[Page extract]
ASTM D349
These test methods cover the procedures for testing rigid round rods used in electrical insulation.
1943
[Page extract]
BS EN ISO 11857
Textile floor coverings, Floor coverings, Sheet flooring, Mechanical testing, Textile testing, Textiles, Tensile testing, Test equipment, Test specimens, Testing conditions.
1944
[Page extract]
BS EN 681-1
This standard specifies requirements for materials used in vulcanized rubber seals for:
1) cold potable water supply (up to 50®C);
1945
[Page extract]
ASTM F2332-06
This specification covers annular ball bearings intended primarily for use in instrument and precision rotating components.
1946
[Page extract]
ISO 14126
ISO 14126 outlines procedures for determining the compressive properties of fibre-reinforced plastics composites in the in-plane direction. Two methods are detailed in the standard:
1947
[Page extract]
SAE AIR 1471A
The purpose of this SAE Aerospace Information Report (AIR) is to provide the aerospace propulsion industry with recommended assembly torque limits for commonly used aircraft propulsion system threaded fasteners when a common torque value per fastener si
1948
Event
Essentials of Adhesion (Peel) Testing
Across many households and industries, consumers have developed a strong preference for and confidence in ‘Duct Tape’ for all types of uses and applications. This is mainly due to the adhesion strength.
1949
[Page extract]
ISO 20126
This International Standard specifies requirements and test methods for the physical properties of manual toothbrushes in order to promote the safety of these products for their intended use.It does not apply to manual interdental brushes and powered or