Search results
2001
[Page extract]
ASTM D3164
Test method ASTM D3164 is used to produce shear strength data for joints to compare adhesives or evaluation surface treatments. Shear joints impose uniform stresses across the bond area which results in the highest possible joint strength.
2002
[Page extract]
ASTM D6415 / D6415M-06a
ASTM D6415 is designed to measure the curved beam strength properties of fiber reinforced composites using a 90˚ curved beam specimen. The curved beam strength represents the moment per unit width which causes a delamination to form.
2003
[Page extract]
SAE AMSSTD
This standard covers the general requirements and methods for testing sandwich core materials and for testing sandwich construction of the types used primarily in aircraft structures.
2004
[Page extract]
ISO 13954
ISO 13954 describes a peel test method for determining the decohesive resistance of polyethylene electrofusion socket assemblies for use in the distribution of fluids.
2005
[Page extract]
ASTM C165
1.1 This test method covers two procedures for determining the compressive resistance of thermal insulations.
2006
[Page extract]
ASTM D 2979
1.1 This test method covers measurement of the pressure sensitive tack of adhesives.
2007
[Page extract]
ASTM D6264 /D6264M-17
In ASTM D6264 a quasi-static indentation (QSI) test method is used to obtain quantitative measurements of the damage resistance of a continuous-fibre-reinforced composite material to a concentrated indentation force
2008
[Page extract]
TAPPI T 807
This method describes a procedure for measuring the bursting strength of linerboard using a disk shaped diaphragm. Basis weights for this method should be 98 g/m (20#/MSF) and higher. The minimum burst should be 350 kPa (51 psi).
2009
[Page extract]
ASTM D380
ASTM D380 is a set of test methods for determining testing and inspection procedures for rubber hoses e.g. hydraulic hoses and automotive hoses.
2010
Event
Introduction to Consumer Packaging Testing
Damaged packaging can not only cost money but also impact brand perception. Consumers are less likely to purchase a product with damaged packaging, or if their product arrives damaged from poor packaging during the shipping and transport process.
2011
[Page extract]
BS EN ISO 4074
BS EN ISO 4074:2002 specifies the minimum requirements and the test methods to be used for condoms made from natural rubber latex which are supplied to consumers for contraceptive purposes and to assist in the prevention of sexually transmitted infectio
2012
[Page extract]
ASTM D906-98
The way adhesives are used in plywood makes shear strength an important performance criteria. Shear strength measured by this test is suitable for use in adhesive development, manufacturing quality control, and in materials performance specifications.
2013
[Page extract]
ASTM D412-16
ASTM D412 is a test standard for testing the tensile stress-strain properties of thermoset rubbers and thermoplastic elastomers. The standard is divided into two test methods.
2014
[Page extract]
ASTM D4475-02
ASTM D4475 is a test method used for determining the horizontal shear strength of fiber reinforced plastic rods.
2016
[Page extract]
ASTM D4964-96
5.1 This test method for testing loop tension and elongation of elastic fabrics is considered satisfactory for acceptance testing of commercial shipments of elastic fabrics because the test method is used in the trade for acceptance testing.
2017
[Page extract]
EN 14488-2
Part 1: Sampling fresh and hardened concrete
Part 2: Compressive strength of young sprayed concrete
Part 3: Flexural strengths (first peak, ultimate and residual) of fibre reinforced beam specimens
2018
Product
ตัวเกจสำหรับอ่านค่าแรงและแรงบิด
AFTI
851-401
ตัวเครื่องแสดงผลการทดสอบแรงและแรงบิดพร้อมเซนเซอร์ที่สามารถใช้ทดแทนกันได้ มีความแม่นยำสูงและมีความยืดหยุ่นในการใช้งาน
เครื่อง AFTI สามารถใช้เป็นอุปกรณ์พกพา เพื่อใช้ร่วมกับอุปกรณ์วัดหรือเซนเซอร์
2020
[Page extract]
Energy
Mecmesin has long been providing force and torque testing solutions to suppliers and contractors into the energy industry...
2021
[Page extract]
Construction
Mecmesin systems and gauges are designed for the application of international and industry standards for quality and safety...
2022
Sensor
Sensors - Vortex-dV
Torque sensors
A range of 'Smart' interchangeable torque sensors are specially adapted for the Vortex-dV test system. Plug and play for automatic calibration and a range of capacities for all requirements, from 1.5 N.m (13 lbf.in) to 10 N.m (90 lbf.in).…
2024
[Page extract]
Bulk analysis
In industries where powders, granules or pelletised materials are formulated, processed or packaged, maintaining consistency in texture and perf
2025
[Page extract]
Automotive
Automotive engineering is a complex area incorporating elements of mechanical, electrical, software and safety engineering. Stringent performance and safety-critical criteria must be met to produce successful vehicles.