Search results
2576
[Page extract]
IEC 60598
IEC 60598-1 specifies general requirements for luminaires, incorporating electric light sources for operation from supply voltages up to 1 000 V.
2577
[Page extract]
ISO 1924-2
Specifies a method for measuring the tensile strength, strain at break and tensile energy absorption of paper and board, using a testing machine operating at a constant rate of elongation (20 mm/min).
2578
[Page extract]
ANSI/EIA 364
Mating and Unmating Procedure for Force Testing of Electrical Connectors and Sockets
2579
[Page extract]
BS EN 13942
This International Standard specifies requirements and provides recommendations for the design, manufacturing, testing and documentation of ball, check, gate and plug valves for application in pipeline systems meeting the requirements of ISO 13623 for t
2580
[Page extract]
ASTM F543-13
This specification provides requirements for materials, finish and marking, care and handling, and the acceptable dimensions and tolerances for metallic bone screws that are implanted into bone.
2581
[Page extract]
BS EN 868-5
Provides examples of particular requirements and test methods for heat and self-sealable pouches and reels manufactured from paper complying with EN 868-3 and plastic film complying with clause 4 of this European standard.
2583
[Page extract]
ASTM D5083-17
ASTM D5083 is a test method for measuring the force required to break a reinforced thermoset plastic specimen and the extent to which the specimen stretches or elongates to that breaking point.
2584
[Page extract]
ISO 10354
Simulates in a qualitative manner the forces and effects on an adhesive-bonded joint at a metal-adhesive/primer interface. It can also be used as a method of checking the surface preparation of substrates.
2585
[Page extract]
Vice grip (Pneumatic)
Vice grips (single-action) - having one fixed jaw against which a second parallel jaw is tightened. The position of the fixed face may be adjustable to accommodate differing specimen thickness.
2586
[Page extract]
TAPPI T 576
This test method decribes the procedure, using constant-rate-of-elongation, for determining three tensile breaking properties of towel and tissue: tensile strength, stretch, and tensi;e energy absorption.
2587
[Page extract]
CETIE Guide 7
This guideline applies to the screw capping of still wines with a metallic closure having a threaded plastic insert and a tamper-evident band which needs to be snapped before it can be opened. The closure is screwed and crimped during capping.
2588
[Page extract]
ASTM D952-15
ASTM D952 is a test method that covers the determination of the bond strength or ply adhesion strength of sheet plastic and electrical insulating materials.
2589
[Page extract]
ISO 188
ISO 188:2011 specifies accelerated ageing or heat resistance tests on vulcanized or thermoplastic rubbers. Two methods are given:
2590
[Page extract]
*corp 01M-01-309
To determine the elongation and recovery properties of elastic Tapes (Both Woven and Knitted), reflectives, elastic tie cords Decorative TPU Bonding and Bonding Tape.
2591
[Page extract]
BS EN 455-2
Protective gloves, Protective clothing, Gloves, Surgical equipment, Sterile equipment, Disposable, Medical equipment, Dimensions, Length, Width, Ageing (materials), Strength of materials, Physical properties of materials, Physical testing
2592
[Page extract]
BS EN ISO 6892-1
This part of ISO 6892 specifies the method for tensile testing of metallic materials and defines the mechanical properties which can be determined at room temperature.
2593
[Page extract]
ASTM C1674
This test method covers the determination of the flexural strength (modulus of rupture in bending) at ambient conditions of advanced ceramic structures with 2-dimensional honeycomb channel architectures.
2594
[Page extract]
USP <381>
This chapter applies to closures used for long-term storage of preparations defined in the general test chapter Packaging and Storage Requirements á659ñ, Injection Packaging.
2595
[Page extract]
ASTM D3481
This test method covers the measurement of the force required to separate (or “shell”) the snap-fitted outer cap from the inner cap of Type IA, IB, or IC child-resistant closures.
2596
[Page extract]
ASTM D751-06
These test methods cover, but are not limited to, rubber-coated fabrics, that is, tarpaulins, rainwear, and similar products.
2597
[Page extract]
Wedge grips
Wedge grips - consisting of 2 interchangeable or fixed jaws in the shape of a wedge which are secured in a metal body.
2598
[Page extract]
ASTM D6534-05
This test method covers the determination of the peak force-to-actuate, sometimes called force-to-actuate (FTA), of a mechanical pump dispenser.
2599
[Page extract]
ISO 29862
This test standard specifies a series of methods for the determination of peel adhesion properties of self adhesives tapes.