Search results
1226
[Page extract]
ASTM D1321
This test method covers the empirical estimation of the consistency of waxes derived from petroleum by measurement of the extent of penetration of a standard needle.
1227
Event
Mechanical Performance Testing of Medical Devices Webinar
A hands-on Force and Torque how-to demonstration event.
1228
[Page extract]
BS EN 1608
This European Standard specifies the equipment and procedures for determining the tensile strength of a product parallel to its faces. It is applicable to thermal insulating products.
1229
Event
Fundamentals of Compression Testing
Push or compressive testing helps determine the limits of most products that require constant pushing or compression.
1230
[Page extract]
IEC 62137-1-1
The test method described in IEC 62137-1-1:2007 is applicable to gull-wing lead surface mounting components.
1231
[Page extract]
ASTM F2458-05
This test method covers a means for comparison of wound closure strength of tissue adhesives used to help secure the apposition of soft tissue.
1232
[Page extract]
IEC 61210
IEC 61210:2010 applies to non-insulated flat quick-connect terminations consisting of a male tab of size 2,8 mm, 4,8 mm, 6,3 mm or 9,5 mm with hole or dimple detents and a mating female connector for use as either an incorporated or an integrated part o
1233
Event
Cap Closure and Removal Torque Testing
The primary objective for measuring and analyzing the torque characteristics of a container cap is to accurately determine not only the quality of the part or process, but also the root cause of a wide variety of defects.
1234
[Page extract]
BS ISO 3597-2
ISO 3597-2 specifies a method for determining the flexural strength of composite rods of circular cross-section made of roving-reinforced resin.
1235
[Page extract]
ASTM D6958-03
These test methods describe an evaluation procedure for the determination of undesirable side-bonding of coatings for wood flooring.
1236
Event
WestPack Expo 2025
Lansmont - together with our sister brand Mecmesin - will be participating in the upcoming WestPack trade show!
1237
[Page extract]
ASTM D3167
ASTM D3167 is used to determine the average peel strength or force of an adhesive and bonding agents through the use of floating roller fixtures. This is used to compare adhesives or to compare adhesive surface preparation procedures.
1238
Test Frame
OmniTest test frame (single column)
OmniTest test frame
A single-column motorised test frame designed to apply tensile, shear, flexural and compressive forces from 2 N right up to a capacity of 7.5 kN (1686 lbf).Its versatile construction makes it perfectly suited for testing all kinds of…
1239
[Page extract]
ASTM F2878-10
This test method is used for determining the force required to cause a hypodermic needle to penetrate through protective clothing material.
1241
[Page extract]
ASTM D229
ASTM D229 is a test method, which provides useful engineering information for evaluating the mechanical behaviour of rigid electrical insulation at elevated temperature.
1242
[Page extract]
BS EN ISO 13934-2
Part 2 of ISO 13934-2 specifies a procedure for the determination of the maximum force of textile fabrics known as the grab test.
1243
Event
WestPack Trade Show
Lansmont - together with our sister brand Mecmesin - will be participating in the upcoming WestPack trade show!
1244
[Page extract]
ASTM D3577
1. Scope ... 1.1 This specification describes certain requirements for packaged sterile rubber surgical gloves used in conducting surgical procedures.
1245
Test Frame
MultiTest test frame (single column)
MultiTest test frame
A ballscrew-driven motorised test frame designed to apply tension and compression from 2 N right up to a capacity of 5 kN (1100 lbf).Its versatile construction makes it perfectly suited for testing all kinds of components in a quality…
1246
[Page extract]
FINAT FTM2
This test method differs from FTM 1 in that it can allow the end user to compare the repositionability of different laminates.
1247
[Page extract]
ASTM F152-95
ASTM F152 is a test standard that covers tensile strength of nonmetallic gasketing materials at room temperature.
1248
[Page extract]
ISO 14126
ISO 14126 outlines procedures for determining the compressive properties of fibre-reinforced plastics composites in the in-plane direction. Two methods are detailed in the standard:
1249
[Page extract]
ASTM D6641 / D6641M - 16e1
The ASTM D6641 test method determines compressive properties of polymer composite materials by applying combined end-loading and shear-loading using a combined loading compression (CLC) fixture.
1250
Event
Live Demonstration: Wire Crimp Tensile Testing
Wire crimp tensile testing provides confidence in the integrity and performance of crimped connections, ensuring reliability, safety, and compliance with industry standards.