Search results
1251
[Page extract]
Torque testing standards
A range of recognised standards define the correct procedures for reverse ratchet torque testing, ensuring consistent and reliable results.
1252
[Page extract]
ASTM F2458-05
This test method covers a means for comparison of wound closure strength of tissue adhesives used to help secure the apposition of soft tissue.
1253
[Page extract]
Standards for bulk analysis testing
Applicable standards and protocols
To ensure consistency and regulatory compliance, bulk testing is often carried out in accordance with established standards. These include:
1254
[Page extract]
BS EN ISO 844
ISO 844 specifies a method of determining a) the compressive strength and corresponding relative deformation, or b) the compressive stress at 10 % relative deformation, and c) when desired, the compressive modulus of rigid cellular plastics.
1255
[Page extract]
CETIE Guide 3
This guide is for producers of quality sparkling wines who carry out the secondary fermentation process in the bottle, also known as bottle fermentation.
1256
[Page extract]
ASTM C1292
This test method covers the determination of shear strength of continuous fiber-reinforced ceramic composites (CFCCs) at ambient temperature.
1257
[Page extract]
Introduction to yield point testing
Yield point testing is essential for understanding the mechanical behaviour of materials.
1258
[Page extract]
FINAT FTM 9
This test method describes a means of assessing probably the most important and yet the hardest to measure property of pressure sensitive materials, the tack.
1259
Bundle
Sharps puncture tester
OmniTest 2.5
BD001
A tester designed for key international standards such as ASTM F2132, BS 7320, and BS 23907 that specify the test procedures for puncture resistance of medical sharps containers.
1260
[Page extract]
ASTM D1578
Significance and Use
Test Method D1578 for testing any spun yarn for breaking strength is considered satisfactory for acceptance testing of commercial shipments since the method has been used extensively in the trade.
1261
[Page extract]
ISO 2493-1
Specifies procedures, based on the two-point loading principle, for determining the bending resistance of paper and board.
1262
[Page extract]
Introduction to fabric testing
Fabric testing plays a critical role in quality assurance, helping manufacturers assess the mechanical, physical, and chemical properties of textile materials.
1263
[Page extract]
Introduction to double rip tongue tear testing
Double rip tongue tear testing is a recognised method for assessing the tear resistance of flexible materials including co
1264
[Page extract]
ASTM D6112-18
ASTM D6112 cover the determination of the creep and creep-rupture properties of plastic lumber and shapes, when loaded in compression or flexure under specified environmental conditions. Test specimens in the “as-manufactured” form are employed.
1265
[Page extract]
Mecmesin equipment for 90-degree peel testing
Mecmesin provides a range of test systems designed for peel and adhesion applications:
1266
[Page extract]
MIL 22520-G
This specification covers the general requirements for crimping tools, accessories and inspection gages used for connecting removable contacts (such as; signal, power, coaxial, shielded, thermocouple, and filter pin contacts) coaxial connectors, shielde
1267
[Page extract]
ASTM D6175-03
5.1 This test method is intended to provide information on the ability of an extruded catalyst to retain physical integrity during use.
1268
[Page extract]
Understanding compressive and tensile forces
Insertion and withdrawal testing focuses on two key force measurements:
1270
[Page extract]
ISO 527-5
ISO 527-5 specifies the test conditions for the determination of the tensile properties of unidirectional fibre-reinforced plastic composites, based upon the general principles given in ISO 527-1.
1271
[Page extract]
ISO 6922
Specifies a method for determining the bond strength of a butt joint when subjected to tensile force. The method is applicable to all types of adhesives.
1272
[Page extract]
Three-point vs four-point bend testing
In a three-point bend test, force is applied at a single midpoint. In a four-point bend test, two loading noses distribute the load over a larger section of the specimen.
1273
[Page extract]
ASTM D7834-13
During the application of coatings, paint brushes can exhibit shedding of filling material onto the coated surface. A measure of this shedding filling material will determine the paint brush’s ability to resist shedding during application.
1274
[Page extract]
ASTM D143
These test methods cover the determination of various strength and related properties of wood by testing small clear specimens.
1275
[Page extract]
Cosmetics & Personal Care Products
Mecmesin solutions for testing in cosmetics and personal care.
Test product formulation for objective texture analysis as well as applicators, dispensers and packaging.