Search results
1976
[Page extract]
ISO 505
ISO 505 specifies a method of test for the measurement of the propagation resistance of an initial tear in textile conveyor belts, either in full thickness or of the carcass only.
1977
Event
Fundamentals of Texture Testing Analysis
The primary goal for using instrumentation to measure texture is to capture an objective value to something that is typically evaluated very subjectively. Texture cannot be controlled unless it measured in a consistent and repeatable manner.
1978
[Page extract]
ASTM D642-00
This test method covers compression tests on shipping containers (for example, boxes and drums) or components, or both. Shipping containers may be tested with or without contents.
1979
[Page extract]
ASTM D3039 / D3039M
ASTM D3039 determines the in-plane tensile properties of polymer matrix composite materials reinforced by high-modulus fibers. A number of calculations can be made including ultimate tensile strength, ultimate tensile strain, tensile chord modulus of
1980
[Page extract]
ASTM D413-98
ASTM D413 is a test method used to determine the force per unit width required to separate a rubber layer from a flexible substrate such as fabric, wire or sheet metal.
1981
[Page extract]
ASTM D3577
1. Scope ... 1.1 This specification describes certain requirements for packaged sterile rubber surgical gloves used in conducting surgical procedures.
1982
Event
Fundamentals of Food Texture Testing and Analysis
Texture cannot be controlled unless it measured in a consistent and repeatable manner.
1983
[Page extract]
IEC 60371-2
Part 1 is definitions of general requirements
Part 3 specifications for individual materials
A number of other non-force/torque properties are tested. This is largely about testing of pressure-bonded laminated materials.
1985
[Page extract]
PSTC 131
SCOPE
1.1 The procedures in this test method describe the measurement of breaking strength, elongation
at break, and energy to break, of pressure sensitive tapes.
1986
[Page extract]
ASTM D3410 / D3410M
ASTM D3410 determines the compressive properties of polymer matrix composite materials reinforced by high-modulus fibers.
1987
[Page extract]
ASTM C203
ASTM C203 is a test method that covers the determination of the breaking load and calculated flexural strength of a rectangular cross section of a preformed block-type thermal insulation tested as a simple beam.
1988
[Page extract]
ASTM D5467 / D5467M-97
ASTM D5467 is a test method that determines the in-plane compressive properties of polymer matrix composite materials reinforced by high-modulus fibers in a sandwich beam configuration.
1989
Event
Fundamentals of Texture Testing Analysis
The primary goal for using instrumentation to measure texture is to capture an objective value to something that is typically evaluated very subjectively. Texture cannot be controlled unless it measured in a consistent and repeatable manner.
1990
[Page extract]
ISO 11502
Describes a qualitative and a quantitative method for assessing the tendency of flexible plastics films and sheets to adhere to one another when left in contact for some time, at a specified temperature and under light pressure.
1991
Event
Essentials of Adhesion (Peel) Testing
Across many households and industries, consumers have developed a strong preference for and confidence in ‘Duct Tape’ for all types of uses and applications. This is mainly due to the adhesion strength.
1992
[Page extract]
ISO 1798
ISO 1798 specifies a method for determining the strength and deformation properties of flexible cellular materials when a test piece is extended at a constant rate until it breaks.
This test standard is equivalent to BS EN ISO 1798:2008
1993
[Page extract]
ISO 36
ISO 36 determines the strength required to separate two plies of fabric bonded together with rubber, or a rubber and a fabric ply bonded together. This test is referred to as a “T-peel” test, because as the two adherends are pulled apart, they form the
1994
[Page extract]
ASTM D1708
ASTM D1708 is used to determine the tensile and elongation properties of small plastic microtensile specimens. These plastic specimens can be of any thickness up to 3.2 mm (1/8 in), including thin films. This test method does not require the use of an
1995
[Page extract]
ASTM D5034-09
This test method covers the grab and modified grab test procedures for determining the breaking strength and elongation of most textile fabrics. Provisions are made for wet testing.
1996
[Page extract]
BS EN 12311-2
BS EN 12311-2 is a test method for determining the tensile properties of flexible sheets used for waterproofing roofs.
1997
[Page extract]
ASTM D2659
ASTM D2659 determines the mechanical properties of blown thermoplastic containers under columnar crush conditions at a steady rate of compression. Any container, whether blown commercially or in the laboratory, may be used as the test specimen.
1998
[Page extract]
BS EN ISO 14129
BS EN ISO 14129 is a test method used to determine the in-plane shear stress/shear strain response of fibre-reinforced plastic components.
