Search results
1376
Event
Needle Sharpness & Puncture Resistance Testing
Hypodermic needles are tested to determine how their design influences the ease of insertion into the skin in order to prevent patient pain and skin trauma.
1377
[Page extract]
BS 4863
Gives safety requirements for playpens for use by children up to 15kg in weight. It covers both rigid sided and mesh sided playpens.
1379
[Page extract]
BS EN 1125
Ironmongery (buildings), Panic bolts, Bolts (security), Emergency exits, Doors, Fire doors, Safety devices, Closing and check mechanisms, Fire safety in buildings, Means of escape from fire in buildings, Hazard prevention in buildings, Buildings open to
1380
[Page extract]
ISBT PTC-00019
This document provides a collection of test methods for the qualification of plastic flat-top closures applied on PET bottles that are used in the beverage industry.
1381
[Page extract]
ASTM D3359
These test methods cover procedures for assessing the adhesion of coating films to metallic substrates by applying and removing pressure-sensitive tape over cuts made in the film.
1382
[Page extract]
ASTM D3846
ASTM D3486 is a test method used for evaluating the in-plane strength of reinforced thermosetting plastics in flat sheet form in thicknesses ranging from 2.54 to 6.60 mm.
1383
[Page extract]
ASTM D3469
These test methods measure the downward forces during the disengagement of lug-style caps from their respective containers. The methods measure the maximum torque developed while the cap is further disengaged by turning of the container.
1384
[Page extract]
BS EN ISO 11608-2
Specifies requirements and test methods for single-use, double-ended, sterile needles for needle-based injection systems (NISs) that fulfil the specifications of ISO 11608-1.
1386
[Page extract]
BS EN 5057
Specifies requirements for dimensions, performance characteristics and test programme. section 16 is insertion & withdrawal force test
1387
[Page extract]
ISO 5628
Specifies three test methods for determining the bending stiffness of paper and paperboard. The test methods differ in the type of loading mode, thus giving rise to the two-point, three-point and four-point bending test methods.
1388
[Page extract]
BS EN 60794-1-21:2015+A1
This part of IEC 60794 applies to optical fibre cables for use with telecommunication equipment and devices employing similar techniques, and to cables having a combination of both optical fibres and electrical conductors.
1390
[Page extract]
ASTM D6109-19
ASTM D 6109 determines the flexural properties for any solid or hollow manufactured plastic lumber product of square, rectangular, round, or other geometric cross section that shows viscoelastic behavior.
1391
Event
Essentials of GRIP & FIXTURE Selection in Force & Torque Testing Webinar
When physically testing a material or component, the ability to apply load to a test specimen is important—but having the ability to apply that load correctly is just as crucial.
1392
[Page extract]
ISO 7886-2
This document specifies requirements for sterile single-use hypodermic syringes of nominal capacity 1 ml and above, made of plastic materials and intended for use with power-driven syringe pumps. Annexe B covers the Pump Force to be measured.
1393
Event
Cork Pull & Cork Compression Testing OnDemand Webinar
FORCE TESTING in Wine & Spirit Applications
1394
[Page extract]
Government
The general government sector covers institutions and public bodies where regulations and standards must be strictly adhered to.
1395
[Page extract]
Comparative analysis with other peel tests
Test type
Peel angle
Common applications
Advantages
1396
[Page extract]
Common challenges and solutions
Misalignment can cause uneven peeling forces.
1397
[Page extract]
Understanding test types
Material testing uses a variety of methods to assess different mechanical properties. Selecting the right test depends on the intended application and relevant standards.
Examples include:
1398
[Page extract]
What is wing tear testing (Winkelmann/Graves method)?
Wing tear testing is a tensile-based method for flexible materials, in which a wing-shaped specimen is subjected to a controlled force until it tears.
1399
[Page extract]
Why Mecmesin?
With over 40 years of experience, Mecmesin delivers torque testing systems that are precise, easy to use, and fully supported.
1400
[Page extract]
Introduction to double rip tongue tear testing
Double rip tongue tear testing is a recognised method for assessing the tear resistance of flexible materials including co