Search results
2251
[Page extract]
ASTM D5528-13
ASTM D5528 is a test method, which determines the opening Mode I interlaminar fracture toughness of continuous fiber-reinforced composite materials. It uses a a double cantilever beam (DCB) specimen. Susceptibility to delamination is one of the major
2252
[Page extract]
ISO 10964
The test method described is used to make comparative assessments of the securing or locking effect of anaerobic adhesives. It may be used for other types of adhesives.
2254
[Page extract]
ASTM D6746-15
ASTM D6746 is a test standard that covers methods to evaluate a characteristic of raw rubber or unvulcanized rubber compounds that is designated as green strength.
2255
[Page extract]
TAPPI T 824
This test evaluates the ability of corrugating medium to contribute to the compression strength of a corrugated box.
2256
[Page extract]
ASTM E328-02
These test methods cover the determination of the time dependence of stress (stress relaxation) in materials and structures under conditions of approximately constant constraint, constant environment, and negligible vibration.
2257
[Page extract]
CETIE Guide 6
This guide gives information on good practice for bottling still wine with an aluminium screw caps on a BVS type glass finish according to EN 16293, with redraw of the cap on application.
2258
[Page extract]
ASTM D4027-98
This test method describes equipment and procedures to measure the shear modulus and shear strength of adhesive layers between rigid adherends.
2259
[Page extract]
ISO 15359
This International Standard specifies, a friction-testing method based on the horizontal plane principle, and the procedure for the determination of the static coefficient of friction before, and static and kinetic coefficients of friction after, a spec
2260
[Page extract]
ASTM D5618-94
This test method covers the measurement of barnacle adhesion in shear to surfaces exposed in the marine environment. It is used to establish the ability of a surface to reduce biofouling adhesion.
2261
[Page extract]
BS EN ISO 7864
BS EN ISO 7864:2016 specifies requirements for sterile hypodermic needles for single use of designated metric sizes 0,18 mm to 1,2 mm.
2262
[Page extract]
ASTM D4501-01
This test method describes a procedure and fixture used to determine shear strengths of adhesives used to bond materials with moduli higher than the modulus of the adhesive.
2263
[Page extract]
SAE USCAR-38
This specification defines basic test methods and requirements for ultrasonically welded cable termination type connections.
2264
[Page extract]
ASTM D3518 / D3518M
ASTM D3518 is a test method, which measure the shear stress and shear strain properties of polymer matrix composite materials composed of +45 plies and -45° plies.
2265
Article/Campaign
Test title
Tensile Testing Solutions
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Fusce ac ipsum varius, porttitor enim eu, porta ipsum. Quisque fermentum dolor est, in interdum purus tincidunt vitae.
2266
[Page extract]
IEC 61210
IEC 61210:2010 applies to non-insulated flat quick-connect terminations consisting of a male tab of size 2,8 mm, 4,8 mm, 6,3 mm or 9,5 mm with hole or dimple detents and a mating female connector for use as either an incorporated or an integrated part o
2267
[Page extract]
ASTM C394
This test method covers determination of the effect of repeated shear loads on sandwich core materials.
2268
[Page extract]
BS EN 17665
The Directive (EU) 2019/904 “on the reduction of the impact of certain plastic products on the environment” introduces the requirement that plastic caps and lids of single use plastic beverage containers up to 3 l capacity shall remain attached to the c
2269
[Page extract]
BS EN 12445
This standard specifies the test methods to be applied to a power operated door to demonstrate compliance with the requirements specidied in EN 12453: 2000 in particular it specifies the method of measuring the forces developed by a power operated door.
2270
[Page extract]
ASTM D6415 / D6415M-06a
ASTM D6415 is designed to measure the curved beam strength properties of fiber reinforced composites using a 90˚ curved beam specimen. The curved beam strength represents the moment per unit width which causes a delamination to form.
2271
[Page extract]
BS EN ISO 527-1
BS EN ISO 527-1 specifies the general principles for determining the tensile properties of plastics and plastic composites under defined conditions.
2272
[Page extract]
ISO 14126
ISO 14126 outlines procedures for determining the compressive properties of fibre-reinforced plastics composites in the in-plane direction. Two methods are detailed in the standard:
2273
[Page extract]
*corp QAC-MC-844
Confidential to l'Oreal
The aim of this test is to check that folding boxes form properly so as to ensure their fluidity of distribution on the filling and packing lines.
2274
[Page extract]
ASTM D6243-09
This test method covers a procedure for determining the internal shear resistance of a Geosynthetic Clay Liner (GCL) or the interface shear resistance between the GCL and an adjacent material under a constant rate of displacement or constant stress.
2275
[Page extract]
IEC 60512-13-1
Details a standard test method to measure the force to fully engage or separate mating connectors, including the effect of any locking, latching, sealing, engaging, separating or similar device, that assists or resists such operation.