Search results
2026
[Page extract]
Consumer Products
Mecmesin test solutions for products typically found in the home ...
2027
[Page extract]
ASTM D876 - 13
ASTM D876 is a test method covering the testing of general-purpose (Grade A), low-temperature (Grade B), and high-temperature (Grade C)2 non-rigid vinyl chloride polymer tubing, or its copolymers with other materials, for use as electrical insulation.
2028
[Page extract]
ASTM C297
This test method determines the flatwise tensile strength of the core, the core-to-facing bond, or the facing of an assembled sandwich panel.
2029
[Page extract]
FINAT FTM1
This test method is designed to quantify the permanence of adhesion or peelability of self-adhesive pressure sensitive) materials.
2030
[Page extract]
ASTM F36-15
The ASTM F36 test method covers the determination of the short-time compressibility and recovery at room temperature of sheet-gasket materials, form-in-place gaskets, and in certain cases, gaskets cut from sheets.
2031
[Page extract]
Step-by-step guide to conducting a CMT test
Prepare the specimen - Cut to size with clean edges, ensuring flutes remain undamaged, and condition as per the standard.
Calibrate the equipment - Check the load cell and platen alignment.
2032
[Page extract]
ASTM C961
This test method covers a laboratory procedure for determining the lap shear strength of sealants. It also provides information on the adhesive bond of the sealants to the tested substrates.
2033
[Page extract]
ASTM D6195-03
These test methods cover the determination of properties of a pressure-sensitive adhesive. These test methods are applicable to those adhesives that form a bond of measurable strength rapidly upon contact with another surface.
2035
[Page extract]
ASTM C674
These test methods cover determination of the modulus of rupture and the modulus of elasticity of fired ceramic whitewares bodies, formed by any fabrication method, and are applicable to both glazed and unglazed test specimens.
2036
[Page extract]
BS EN 1492-1
Specifies the requirements related to safety, including methods of rating and testing single-, two-, three-, four-leg and endless sewn flat woven webbing slings, with or without fittings, made of polyamide, polyester and polypropylene man-made fibre web
2037
[Page extract]
BS EN 1465
Specifies a method for determining the tensile lap-shear strength of bonded assemblies when tested on a standard specimen and under specified conditions of preparation and testing.
2038
[Page extract]
SAE J174M
This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque type threaded steel fasteners 6 through 24 mm nominal diameters.
2039
[Page extract]
BS EN 50289-3-17
Communication cables, Electric cables, Communication transmission lines, Mechanical testing, Adhesion tests, Dielectric materials, Cable sheaths
2040
[Page extract]
BS 2782-12: 1210A to C
BS 2782-12: Method 1210A to C specifies a test method for testing the longitudinal tensile properties of glass-reinforced thermosetting plastics (GRP) pipes.
2041
[Page extract]
Applications of edge crush testing in packaging
Design and development
ECT results guide engineers in selecting the correct board grade for the intended application, balancing performance and cost.
2042
[Page extract]
ISO 8113
ISO 8113 specifies a method for determination of the resistance of glass containers to external force in the direction of the vertical axis.
2043
[Page extract]
BS EN 12814-1
BS EN 12814-1 is a bend test method for testing welded joints of thermoplastics semi-finished products.
2044
[Page extract]
BS EN ISO 1856
BS EN ISO 1856 is a test method that specifies three methods for determining the compression set of flexible cellular materials and applies only to latex and polyurethane foams of thickness greater than 2 mm.
2045
[Page extract]
ISO 8627
Specification of a test method and grading scheme for the stiffness of the tufted area of conventional manual tooth-brushes, together with the relevant information concerning definitions and those concerning testing machines.
2046
[Page extract]
SAE J 1907
This recommended practice defines a procedure for the construction and testing of a 180 deg peel specimen for the purpose of determining the bondability of glass to elastomeric material in automotive modular glass.
2047
[Page extract]
BS ISO 3597-2
ISO 3597-2 specifies a method for determining the flexural strength of composite rods of circular cross-section made of roving-reinforced resin.
2048
[Page extract]
ASTM D7264 / D7264M-15
ASTM D7264 is a test method used to determine the flexural stiffness and strength properties of polymer matrix composites. The test method summarises two procedures:
2049
[Page extract]
FINAT FTM2
This test method differs from FTM 1 in that it can allow the end user to compare the repositionability of different laminates.
2050
[Page extract]
BS EN ISO 376
BS EN ISO 376:2011 looks at the calibration of force-proving instruments used for the static verification of uniaxial testing equipment. These include tension and compression testing machines.