Search results
1001
[Page extract]
BS EN 12209
BS EN 12209:2016 specifies requirements and test methods for the durability, strength, security, and function of mechanically operated locks and latches and their locking plates for use in doors, window doors and entrance doors in buildings.
1002
[Page extract]
BS ISO 7743
ISO 7743 specifies methods for the determination of the compression stress-strain properties of vulcanized or thermoplastic rubber using a standard test piece, a product or a part of a product.
Four procedures are given:
1003
Case study
Stabilised spring testing
Customised engineering example
Our client needed to test a number of small, lightweight springs under compression. To avoid buckling and sideways movement of the springs, a supporting spindle or guide-rod was required.
1004
Page
Contact sales
Looking for the right testing solution?
Our experts are ready to help - just complete the form below and one of our Technical Sales Engineers will be in touch.
1005
[Page extract]
ASTM C1147
ASTM C1147 testing covers the evaluation of joints between two pieces of weldable grades of thermoplastic material. This testing is intended to establish methods to evaluate minimum short term weld factors.
1006
[Page extract]
ISO 1926
ISO 1926 specifies a method of determining the behaviour of rigid cellular plastics materials when they are subjected to a tensile stress.
1007
[Page extract]
SAE USCAR-21-4
This specification defines test methods and requirements for validation of solderless crimped connections.
1008
Event
Pull Force and Break Strength Testing
Whether it is medical tubing, plastic straws, copper wire or zip ties, pull force and break strength testing is critical not only to production quality but also to consumer safety.
1009
[Page extract]
TAPPI T 825
The flat crush test (1) is a measure of the resistance of the flutes in corrugated board to a crushing force applied perpendicular to the surface of the board under prescribed conditions.
1010
[Page extract]
Force systems
Do you need a level of accuracy and repeatability which just cannot be achieved by manual testers?
1011
[Page extract]
Bulk analysis
In industries where powders, granules or pelletised materials are formulated, processed or packaged, maintaining consistency in texture and perf
1012
[Page extract]
Compression
Compression testing is a way of determining how something will react when a compressive force is applied to it. It typically involves measuring the relationship between the applied force and how much the object deforms.
It is performed to:
1013
Sensor
Sensors - Universal Testers (ELS)
Sensors
The OmniTest universal testers use Mecmesin's range of high-resolution precision Enhanced Load Sensors (ELS) to record tensile and compressive loads.
ELSA precision loadcell connects directly to an OmniTest or MultiTest-dV stand and communicates…
1014
[Page extract]
What is the edge crush test and why is it important?
ECT assesses the capacity of corrugated board to withstand compressive forces along its edge. A higher ECT value generally means the board has greater stacking strength.
1015
[Page extract]
Jewellery & Watch
In jewellery and watch production, alloys, components and other materials must meet the needs of the manufacturing process and the end-product should give good service performance when worn by the customer.
1016
Accessory
FINAT 1 Peel Jig for 180 degree testing, QC-20
PDV13016-C
FINAT 1 Peel Jig - 180°
A polished steel plate used for affixing pressure-sensitive adhesive tape in accordance with FINAT 1 test method and other international standards.
Fitted with an adaptor having QC-20mm female hole for connection to the base of…
1017
Accessory
Footswitch regulator option
Mec205-PR
Pressure regulator to adjust the air pressure between 1-10 bar.
Useful when a different pressure is required between upper and lower pneumatic grips.
To be ordered and fitted with either Mec205-1 or Mec205-2 Footswitches.
1018
Accessory
Miniature Vice Grip, 100 N, QC-20 fitting
MecS341
Versatile, easy to use, and suitable for small components (eg bonded joints) where access is limited and tensile forces are below 100 N.
Clamping surfaces are machined with pyramid-shaped serrations to ensure optimum gripping force.
The flexible chain-…
1019
Accessory
Charger for digital gauges, UK, 230 V, 3-pin square
304-005
For use with Mecmesin digital force and torque gauges. 230 Volt with 3 square pins. Commonly used in the UK.
The mains adaptor/charger is a constant-current type:
Primary circuit: 230V – 50Hz
Secondary circuit: 100mA constant current at 9V Charger…
1020
Accessory
Dial Gauge Bracket Set
432-167
The dial gauge bracket set allows an analogue or digital comparator to be securely fitted to the MDD manual test stand. Digital comparators are suitable for measuring crosshead movement over short distances.
1021
Accessory
Diamond coated jaws for Mec83 U-Form Pneumatic Vice Grip, 5 kN, 40 x 60 mm
Mec83-BD
Diamond Jaws (40mm x 60mm) - nickel-plated having clamping surface coated with synthetic diamonds.
Opening span = 0-10mm, 10-20mm or 20-30mm depending on which rod and piston are fitted to the Mec83 body.
For materials which need a “bite” to secure a…
1022
Accessory
Compression Plate, Self-levelling, Hardened & Ground, 70 mm, 5-16 UNC
432-350
Self-levelling compression plates are ideal for general compression testing on a range of materials and finished products. Self-levelling allows parallelism to be set for those applications where it is critical to accurately measure the deformation of a…
1023
Accessory
Diamond coated jaws for Mec240k Medium Vice Grip, 30 x 30 mm
Mec240k-BD
Diamond Jaws (30mm x 30mm) - nickel-plated having clamping surface coated with synthetic diamonds.
Opening span = see datasheet for various spans according to the grip body selected.
For materials which need a “bite” to secure a good grip (e.g. soft…
1024
Accessory
Compression Plate Square, Hardened Steel, 196 x 196 mm, QC-20 or QC-32 fitting
Mec36-196-St
MEC36-196-St :-
Square compression plate in hardened steel featuring concentric circles for helping operators to place samples centrally. Also supplied with 4 fixing legs to support the weight of the steel plate. Suitable for hard specimens such as…
1025
Accessory
Lightweight hanger and 5 N slotted mass for verifying FPT 10 N
432-655
A lightweight hanger and an M1 slotted mass of 5N.
For use with the FPT-H1 loadcell calibration checking kit (432-635) to verify the accuracy of HILC 10 N loadcells.