Search results
826
[Page extract]
ASTM D3518 / D3518M
ASTM D3518 is a test method, which measure the shear stress and shear strain properties of polymer matrix composite materials composed of +45 plies and -45° plies.
827
[Page extract]
ISO 1924-1
Applies, within the limitations of the instruments used, to all papers and boards with the exception of corrugated board, but may be applied to the components of such board. Specifies the method which causes failure of the piece in a mean time of 20 s.
828
[Page extract]
ASTM F543-13
This specification provides requirements for materials, finish and marking, care and handling, and the acceptable dimensions and tolerances for metallic bone screws that are implanted into bone.
829
[Page extract]
BS EN 1400
Babies dummies, Baby equipment, Children, Chemical analysis and testing, Chemical hazards, Toxic materials, Dangerous materials, Mechanical testing, Performance testing, Safety measures, Packaging, Marking, Instructions for use.
830
[Page extract]
BS EN 2591-418
Describes a method of determining the insertion/extraction forces of female contacts used in elements of electrical and optical connection by means of gauges.
831
Case study
Respiratory device spring test
Requirement
Bespak is a leader in specialty medical devices for inhaled drug delivery and anaesthesia.
832
[Page extract]
ANSI/EIA 364-38B
This standard establishes a test method to determine the axial tensile load that can be applied to a mated pair of connectors and the holding effect of a connector cable clamp without causing any detrimental effects upon the cable or connector when subj
834
Case study
航空機ブレーキユニットのばね試験
要件ブリティッシュ・エアウェイズplcの航空機ホイールおよびブレーキ部門は、ボーイング737、747、757、777およびエアバスA319、A320、A321航空機の航空機ブレーキユニットの修理とオーバーホールを担当しています。ブレーキユニットのスプリングをテストすることは、ピストンが伸縮すること、およびこれらの安全上重要なコンポーネントが正しく機能することを確認するためのオーバーホールプロセスの重要な部分です。
835
[Page extract]
ASTM D6004-04
This test method describes a procedure to measure shear strength development for adhesives used to bond carpet adhesives to selected underlayments.
837
Case study
Cable duct strength testing
Customised engineering example
Our customer manufactures tubes and ducts for routing of cables and optical fibres. Installation of these uses blowing, pushing and pulling techniques.
838
[Page extract]
ASTM D6496-04a
This test method covers the laboratory determination of the average bonding strength between the top and bottom layers of a sample of a geosynthetic clay liner.
839
[Page extract]
BS EN 1464
Specifies a floating roller method for the determination of the peel resistance of adhesive bonds between one rigid adherend and one flexible adherend when tested under specified conditions of preparation and testing.
840
[Page extract]
BS EN ISO 11608-3
Medical equipment, Medical instruments, Parenteral infusion equipment, Injection instruments, Injection guns, Syringes, Drug administration, Measuring cylinders, Containers, Performance testing, Performance, Leak tests, Design, Dimensions
841
[Page extract]
NF S86-604
This document defines the test methods for characterizing metallic watch straps and the corresponding requirements.
842
[Page extract]
ISO 13445
Specifies a method for the determination of the shear strength of adhesives used to bond materials with elastic moduli higher than the elastic modulus of the adhesive.
843
[Page extract]
ISO 4049
This document specifies requirements for dental polymer-based restorative materials supplied in a form suitable for mechanical mixing, hand-mixing, or intra-oral and extra-oral external energy activation, and intended for use primarily for the direct or
845
[Page extract]
ISO 10964
The test method described is used to make comparative assessments of the securing or locking effect of anaerobic adhesives. It may be used for other types of adhesives.
846
[Page extract]
TAPPI T 824
This test evaluates the ability of corrugating medium to contribute to the compression strength of a corrugated box.
848
Case study
High Performance Plasma Coatings
Requirement
Alphatek Hyperformance Coatings Ltd. are a coatings company that applies wear, corrosion, heat or electrically resistive coatings, supplying to many different industries.
849
[Page extract]
ASTM C1341
This test method covers the determination of flexural properties of continuous fiber-reinforced ceramic composites in the form of rectangular bars formed directly or cut from sheets, plates, or molded shapes.
850
[Page extract]
ASTM D6241-04
This test method for determining the puncture strength of geotextiles is to be used by the industry as an index of puncture strength.