Search results
701
Case study
Granule hardness test
Requirement
Ecosyl Products Limited is one of the world's leading companies involved in the sales and marketing of forage additives for the agricultural industry.
702
[Page extract]
Abrasion
Abrasion is the surface wear caused by rubbing with another material. The consumer would expect textiles and other products to withstand a certain amount of deterioration.
703
Case study
Golf ball deflection test
Requirement
A golf ball manufacturer has factories based in both the US and India.
704
[Page extract]
Measurement and testing methods
Techniques for measuring tangent modulus
Tangent modulus is measured during tensile or compression testing, w
705
[Page extract]
Understanding corrugated cardboard resistance
The compressive resistance of corrugated cardboard depends on factors such as flute profile, board structure, and paper quality.
706
[Page extract]
Relevant textile test standards
The strip method is defined in several national and international standards, each tailored to specific fabric types and performance requirements:
707
[Page extract]
Loop tack test standards
Several international standards govern loop tack testing to ensure results are consistent and repeatable:
708
[Page extract]
Standards for 180 degree peel testing
A number of standards define the correct method for performing a 180 degree peel test.
709
[Page extract]
Introduction to compressibility and recovery testing
Compressibility and recovery testing measures how a material behaves under load and how effectively it returns to its original form once the load is removed.
710
[Page extract]
Key features and advantages
The strip method offers a number of engineering advantages:
711
[Page extract]
Key standards in compressive deformation testing
Compliance with recognised standards ensures that results are accurate, repeatable, and accepted by regulatory bodies. Examples include:
712
[Page extract]
Torque testing standards
A range of recognised standards define the correct procedures for reverse ratchet torque testing, ensuring consistent and reliable results.
713
[Page extract]
Standards for friction testing
Mecmesin systems comply with a range of international standards to ensure consistency and comparability of results:
714
[Page extract]
Standards for the peel wheel test
Standardisation ensures peel wheel tests are consistent and repeatable across laboratories and production sites.
716
[Page extract]
Benefits of box crush and packaging compression tests
Compression testing offers both commercial and technical benefits for manufacturers and logistics operations.
717
[Page extract]
Testing solutions and equipment
Essential equipment
Cone point probe - typically 8 mm in diameter with capacity for up to 500 N.
718
[Page extract]
Common challenges and best practices
Accurate four-point bend testing requires attention to several factors:
719
[Page extract]
Understanding torque testing
Types of torque testing in packaging
Several torque measurements are relevant to closure performance:
720
[Page extract]
Methods and applications
Common test methods
Most single lap shear tests are carried out under tensile loading, but the method can vary depending on material type, bond configuration and industry require
721
[Page extract]
Government
The general government sector covers institutions and public bodies where regulations and standards must be strictly adhered to.
722
Sensor
Sensors - Universal Testers (ELS)
Sensors
The OmniTest universal testers use Mecmesin's range of high-resolution precision Enhanced Load Sensors (ELS) to record tensile and compressive loads.
ELSA precision loadcell connects directly to an OmniTest or MultiTest-dV stand and communicates…
723
Accessory
Automated Syringe Batch Tester
PDV19179
The Automated Syringe Batch tester is a bench-top system for checking the ‘break-loose’ and ‘glide force’ of up to 12 individual syringes in one ‘load-and-run’ cycle. In the face of increased demand on production of syringes, this system enables larger…
724
Accessory
Wedge Grip (small), 500 N, 10-32 UNF
432-385
The small, lightweight Wedge Grip is ideal for tensile testing below 500 N.
A spring-loaded lever ensures the serrated jaws (16mm wide x 20mm high) are easy to open for fast securing and release of samples. As load is applied, the self-tightening action…
725
Accessory
Self-levelling Compression Plate Steel - 116 mm, 50 kN, QC-32 fitting
MecS223g-116
MecS223g - 116mm diameter Self-levelling Compression Plate:
Self-levelling allows exact parallelism to be set between the upper and lower plates - ideal for those applications where it is critical to accurately measure the deformation of a sample.
The…