Search results
2576
[Page extract]
BS EN 671-1
Fire hydrants, Fire hoses, Firefighting equipment, Flexible pipes, Fire hose reels, Hose reels, Fire safety in buildings, Performance, Approval testing, Corrosion tests, Ageing tests, Flow measurement, Endurance testing, Impact testing, Pressure testing
2577
[Page extract]
BS EN ISO 10619-1
BS EN ISO 10619-1 is a test method covering bending tests on rubber or plastics hoses and tubing.
2578
[Page extract]
GS1 5.0
The Hanger Specifications are intended to increase efficiency in the supplier-to-retailer pipeline by minimizing order-to-sales floor cycle time.
2579
[Page extract]
TAPPI T 549
This method describes a horizontal plane procedure for the determination of the coefficient of static and kinetic friction of paper measured when sliding against itself.
2580
[Page extract]
BS EN 12562
Synthetic fibres, Polyamide fibres, Aramide fibres, Textile products, Textile testing, Yarn, Filament yarns, Filaments, Filament (textile fibre), Yarn testing, Yarn linear density determination, Elongation at fracture, Elongation, Force measurement, Mec
2581
[Page extract]
BS EN 12568
Protective footwear, Protective clothing, Toe-caps, Metals, Non-metals, Impact strength, Performance testing, Dimensions, Length, Impact testing, Compression testing, Penetration tests, Corrosion resistance, Corrosion tests, Bend testing, Marking, Test
2582
[Page extract]
ASTM D2718
These test methods determine the shear properties of structural panels associated with shear distortion of the planes parallel to the edge planes of the panels. Both shear strength and modulus of rigidity may be determined.
2583
[Page extract]
ISO 1924-1
Applies, within the limitations of the instruments used, to all papers and boards with the exception of corrugated board, but may be applied to the components of such board. Specifies the method which causes failure of the piece in a mean time of 20 s.
2584
[Page extract]
ASTM D4482-11
ASTM D4482 is a test method used to determine the fatigue life of rubber compounds undergoing a tensile-strain cycle. During part of the cycle, the strain is relaxed to a zero value.
2585
[Page extract]
BS EN ISO 8317
This is the panel testing by children and adults that has to be done before machine testing is used to test subsequent minor design changes.
2586
[Page extract]
ASTM B913
This test method establishes the requirements for a standardized method of evaluating the quality of crimped-type electrical connections to solid or stranded conductors.
2587
[Page extract]
ISO 2555
Specification of a method for determining an apparent viscosity of resins in a liquid state, using one of the types of rotational viskosimeter described in this standard.
2588
[Page extract]
ASTM D6713-14
Materials shall be tested and the individual grades shall conform to specified values of the physical properties such as tensile strength, tensile elongation, tensile modulus, dimensional stability, flexural modulus, and Izod impact; and dimensional pro
2589
[Page extract]
BS 5081-1
A mechanical testing machine is used to move the syringe plunger and to aspirate and expel water, whilst the force exerted and the plunger travel are recorded.
2590
[Page extract]
ASTM D6117-18
ASTM D6117 covers the evaluation of fastener use with “as manufactured” plastic lumber and shapes through the use of two different testing procedures:
2591
[Page extract]
ASTM D2653
ASTM D2653 determines the tensile properties of elastomeric yarns made from natural rubber, spandex or other elastomers.
2592
[Page extract]
TAPPI T 810
This method describes a procedure for measuring the bursting strength of single wall and double wall corrugated board within the range of 690 kPa (100psi) to 4825 kPa (700 psi) employing an instrument which uses a disk shaped, molded diaphragm.
2593
[Page extract]
DIN EN 61238-1
Electric connectors, Crimped connectors, Electric cables, Power cables, Electric conductors, Electric wires, Copper, Aluminium, Temperature, Classification systems, Type testing, Short-circuit current tests, Resistance measurement, Mechanical testing, T
2594
[Page extract]
ASTM D3807
ASTM D3807 is a test method used to determine the strength properties of adhesives in cleavage peel by tension loading. It allows the comparative testing of cleavage/peel strengths of bonded engineering thermoplastic adherends.
2595
[Page extract]
ASTM F1473-18
ASTM F1473 is a test method determines the resistance of polyethylene materials to slow crack growth. It is also known as PENT (Pennsylvania Notch Test) test.
2596
[Page extract]
ASTM D2370
This test method covers the determination of the elongation, tensile strength, and stiffness (modulus of elasticity) of organic coatings when tested as free films.
2597
[Page extract]
ASTM E8/E8M-13a
These test methods cover the tension testing of metallic materials in any form at room temperature, specifically, the methods of determination of yield strength, yield point elongation, tensile strength, elongation, and reduction of area.
2598
[Page extract]
BS EN ISO 10591
This International Standard specifies a method for the determination of the influence of water on the adhesion cohesion properties of sealants with predominantly plastic behaviour which are used in joints in building construction.
2599
[Page extract]
BS EN ISO 9001
ISO 9001 has been revised to reflect the many changes in the way we now do business – new technology, greater access to information, higher customer expectations, globalization and increasing importance of service industries.
2600
Event
Tensile Testing: Basics, Tips and Trends
Have you ever wondered if the seatbelt in your vehicle is strong enough to restrain you in a collision? How about the average person pulling the cork out of a wine bottle?