Search results
1226
[Page extract]
Manual test stands
Manual test stands allow simple force testing when budgets are limited.
Lever-operated models enable rapid testing of tension and compression up to 500 N.
1227
[Page extract]
Methods and applications
Common test methods
Most single lap shear tests are carried out under tensile loading, but the method can vary depending on material type, bond configuration and industry require
1228
[Page extract]
ASTM D3474
This standard covers the calibration and use of torque meters of the type normally used in packaging applications.
1229
[Page extract]
Mecmesin equipment for 180 degree peel testing
Mecmesin provides a complete range of test solutions designed for accurate and repeatable peel strength measurement.
1230
[Page extract]
ISO 20502
SO 20502:2005 describes a method of testing ceramic coatings by scratching with a diamond stylus.
1231
[Page extract]
ASTM D349
These test methods cover the procedures for testing rigid round rods used in electrical insulation.
1232
[Page extract]
ASTM D5934-02
ASTM D5934 specifies the use of controlled rate of loading mechanical instrumentation on rectangular plastic bars molded directly or cut from sheets, plates, or molded shapes via three-point loading bending techniques to obtain material properties such
1233
Software
VectorPro Lite software (force instruments)
VectorPro® Lite software
Available as an optional extra to Mecmesin's Digital Force Gauges (VFG, AFG, BFG and CFG+ and VFTI/AFTI Digital Force Indicators, VectorPro Lite is an advanced data acquisition and plotting software package.
Simply select the…
1234
[Page extract]
Application of standards in puncture testing
Standardised methods ensure test consistency and reliability across laboratories and production sites.
1235
[Page extract]
Standards for box crush testing
ASTM D642-00
This standard specifies methods for determining the compressive resistance of shipping containers, both filled and empty.
1236
[Page extract]
ASTM D5748-95
This test method determines the resistance of a stretch wrap film to the penetration of a probe at a standard low rate, a single test velocity.
1237
[Page extract]
Standards and guidelines for torque testing
Overview of ASTM and CETIE standards
Standardised testing ensures consistency and compliance. Commonly followed guidelines include:
1238
[Page extract]
Introduction to peel wheel testing
The peel wheel test is a specialised adhesion test method used to measure the strength of adhesive bonds in flexible materials such as plastics, films, and laminates.
1239
[Page extract]
Why Mecmesin for bulk analysis
Expert engineering and equipment
Mecmesin systems are designed for precision and reliability in bulk testing applications.
1240
Event
Makers Hackathon, June 16-18th 2022, Malmö, Sweden
Who should attend?
Quality Managers, design/product engineers and materials specialist.
What is the exhibition about?
1241
[Page extract]
How to Calculate UTS
This gives a value in N/mm² or MPa. During a tensile test, the material is pulled until it breaks. The highest recorded force, divided by the original cross-sectional area, gives the UTS. This value is the peak on a stress-strain curve.
1242
[Page extract]
ASTM D7078/D7078M-12
This test method covers the determination of the shear properties of high-modulus fiber-reinforced composite materials by clamping the ends of a V-notched specimen between two pairs of loading rails.
1243
[Page extract]
ASTM D4541-09e1
This test method uses a class of apparatus known as portable pull-off adhesion testers. They are capable of applying a concentric load and counter load to a single surface so that coatings can be tested even though only one side is accessible.
1244
[Page extract]
Introduction to Delft tear testing
The Delft tear test is a specialised method for determining the tear strength of vulcanised rubber, thermoplastic elastomers and similar flexible materials.
1245
[Page extract]
FINAT FTM 9
This test method describes a means of assessing probably the most important and yet the hardest to measure property of pressure sensitive materials, the tack.
1246
[Page extract]
BS ISO 11193-1
ISO 11193-1:2008 specifies requirements for packaged sterile, or bulked non-sterile, rubber gloves intended for use in medical examinations and diagnostic or therapeutic procedures to protect the patient and the user from cross-contamination.
1247
[Page extract]
Introduction to tensile testing
Tensile testing is one of the most widely used methods in material science for determining the mechanical properties of materials under uniaxial tension.
1248
[Page extract]
Importance of ergonomic strength testing
Ergonomic strength testing is essential for ensuring that human performance matches task requirements. This alignment reduces the risk of musculoskeletal injuries and improves long-term health outcomes.
1249
[Page extract]
BS EN ISO 844
ISO 844 specifies a method of determining a) the compressive strength and corresponding relative deformation, or b) the compressive stress at 10 % relative deformation, and c) when desired, the compressive modulus of rigid cellular plastics.
1250
[Page extract]
ASTM D5034-09
This test method covers the grab and modified grab test procedures for determining the breaking strength and elongation of most textile fabrics. Provisions are made for wet testing.