Search results
2952
Event
Wine & Spirits Capping: Cork Pull & Twist Caps
Wine packaging has a great influence on the quality of the product delivered to the customer.
2953
[Page extract]
*corp QPF-MC-1209 B
*Strictly confidential*
L'Oreal to methods for shear and penetration testing of lipsticks, deodorants etc.
2954
[Page extract]
BS EN 12467
Sheet materials, Asbestos cement, Cements, Fibres, Reinforced materials, Sheet roof coverings, Cladding (buildings), Curtain walling, Grades (quality), Density, Strength of materials, Approval testing, Type testing, Quality control, Acceptance inspectio
2955
[Page extract]
ASTM D5672-09
This test method covers a screening type quality control test used to determine if flexible polyurethane foam cushions are within the specified grade range for firmness.
2956
[Page extract]
EN 12089
Thermal insulating materials, Bend testing, Construction materials, Loading, Deflection tests, Mechanical testing, Testing conditions, Test equipment, Test specimens, Reports, Accuracy, Reproducibility.
2957
[Page extract]
NF S86-604
This document defines the test methods for characterizing metallic watch straps and the corresponding requirements.
2958
[Page extract]
BS EN ISO 10590
This International Standard specifies a method for the determination of the influence of water immersion on the adhesion/cohesion properties at maintained extension of sealants used in joints in building construction.
2959
[Page extract]
BS EN ISO 6892-2
BS EN ISO 6892-2 specifies a method of tensile testing of metallic materials at temperatures higher than room temperature.
2960
[Page extract]
ASTM D7834-13
During the application of coatings, paint brushes can exhibit shedding of filling material onto the coated surface. A measure of this shedding filling material will determine the paint brush’s ability to resist shedding during application.
2961
[Page extract]
ASTM D3822
This test method covers the measurement of tensile properties of natural and man-made single textile fibers of sufficient length to permit mounting test specimens in a tensile testing machine.
2962
[Page extract]
NF G30-102
La présente partie a pour objet de décrire une méthode de mesure directe de la pression de contention des garnitures élastiques telles que les bords-côtes de chaussettes, ceinturesde slips et de culottes, gaines et bas dits de confort, et plus généralem
2963
[Page extract]
ASTM D7264 / D7264M-15
ASTM D7264 is a test method used to determine the flexural stiffness and strength properties of polymer matrix composites. The test method summarises two procedures:
2964
[Page extract]
ASTM D3518 / D3518M
ASTM D3518 is a test method, which measure the shear stress and shear strain properties of polymer matrix composite materials composed of +45 plies and -45° plies.
2965
[Page extract]
ASTM F1473-18
ASTM F1473 is a test method determines the resistance of polyethylene materials to slow crack growth. It is also known as PENT (Pennsylvania Notch Test) test.
2966
[Page extract]
ISO 3037
Specifies an unwaxed edge method for the determination of the edgewise crush resistance of corrugated fibreboard. It is applicable to all corrugated fibreboard grades.
2967
[Page extract]
ASTM E8/E8M-13a
These test methods cover the tension testing of metallic materials in any form at room temperature, specifically, the methods of determination of yield strength, yield point elongation, tensile strength, elongation, and reduction of area.
2968
[Page extract]
ISO 2493-1
Specifies procedures, based on the two-point loading principle, for determining the bending resistance of paper and board.
2969
[Page extract]
Vice grip (Mechanical)
Vice grips (single-action) - having one fixed jaw against which a second parallel jaw is tightened. The position of the fixed face may be adjustable to accommodate differing specimen thickness.
2970
[Page extract]
ASTM D6797-07
This test method describes the measurement for bursting strength of woven and knitted textiles taken from rolls of fabric or fabric taken from garments.
2971
Event
Advanced Engineering 2021 - We would love to see you there!
Who should attend?
Engineering professionals and managers from advanced manufacturing sectors interested in quality assurance testing solutions.
What is the exhibition about?
2973
Test Frame
Vortex-dv test frame
Vortex test frame
A sturdy twin-column test frame capable of applying torque up to 10 N.m (90 lbf.in). Tall and wide enough to accept a variety of test specimens yet compact to use as a bench-top tester.
View test frame
2974
[Page extract]
BS EN 302-1
Adhesives, Phenolic resins, Aminoplasts, Plastics, Wood, Structural timber, Test specimens, Dimensions, Specimen preparation, Testing conditions, Adhesion tests, Tensile testing, Shear testing, Construction materials, Adhesive-bonded joints, Adhesive st
2975
[Page extract]
ASTM D2653
ASTM D2653 determines the tensile properties of elastomeric yarns made from natural rubber, spandex or other elastomers.