Search results
2676
[Page extract]
BS 4839
Specification for Blow moulded polyolefin containers, part 2: Plastics containers. Containers over 5 litres and up to 60 litres capacity
2677
[Page extract]
BS ISO 2285
BS ISO 2285 is a test method for determining the tension set under constant elongation of vulcanised rubber or thermoplastic.
2678
[Page extract]
Agricultural
Throughout the production chain, crops, animal feedstuffs and produce are driven to meet quality standards, and to match up to trade and consumer expectations.
2679
[Page extract]
SAE J 1907
This recommended practice defines a procedure for the construction and testing of a 180 deg peel specimen for the purpose of determining the bondability of glass to elastomeric material in automotive modular glass.
2680
[Page extract]
Compression
Compression tests are performed to evaluate the performance of a material or component under gradually increasing compressive load.
2681
Case study
Insulation film stiffness testing
Customised engineering example
Familiar with three-point bending to test flexural strength properties?
2682
Event
Medical Devices: General testing with 21 CFR Part 11 compliance
Reliable results, trusted compliance: 21 CFR Part 11's role in securing medical device quality testing.
Quality testing of Medical Devices ranges from syringe actuation (break loose and glide), needle sharpness and adhesion strength to Child R
2683
[Page extract]
TAPPI T 556
This procedure is used to measure the bending resistance of paper and paperboard in the machine and cross machine directions, by determining the bending resistance in mN of a 38mm (1.5in) wide vertically clamped sample, at 15o or 7.5o deflection.
2684
[Page extract]
PSTC 8
Unwind adhesion is a quantitative measure of the degree of ease or difficulty in unwinding a roll of tape.
The test specimen shall be any 10 m (10 yard) or more roll of pressure sensitive tape - preferably 24 mm (1”) wide.
2685
[Page extract]
ISBT PTC-00004
These ISBT (International Society of Beverage Technologists) Sport Closure test methods focus on child safety related parameters such as separation forces and choking hazards of closure components.
2686
[Page extract]
ASTM E855-08
This standard describes three test methods for determining the modulus of elasticity in bending and the bending strength of metallic strips or sheets intended for the use in flat springs.
2687
Page
Contact support
Experiencing an issue or need technical guidance?
Our Support Team is here to help troubleshoot and resolve your problem. Fill out the form and we’ll be in touch as soon as possible.
2688
[Page extract]
BS EN ISO 2060
Cancels and replaces the first edition (1972). Specifies a method for the determination of the linear density of all types of yarn in package form. Includes seven optional procedures based on different methods of conditioning and preparation.
2689
[Page extract]
ISO 7810
Stipulates test method as per ISO/IEC 10373-1 for determining the Peel Strength of cards.
2690
Case study
Integrità del disco abrasivo dentale
Requisiti La resistenza allo scivolamento della crimpatura dell'occhiello al centro di un disco abrasivo dentale è una misura chiave della qualità del prodotto.
2691
Event
Tensile Testing: Basics, Tips and Trends
Have you ever wondered if the seatbelt in your vehicle is strong enough to restrain you in a collision? How about the average person pulling the cork out of a wine bottle?
2692
[Page extract]
Sistemi di coppia
Hai bisogno di un livello di precisione e ripetibilità che non può essere raggiunto dai tester manuali?
2693
Case study
Lighting weld test
Requirement
A simple, low-cost fixture was specified by the customer for the Quality Control Laboratory. This was to hold a lighting assembly in a test where the welded contacts were pulled off.
2694
[Page extract]
BS ISO 4919
Specifies a method for determination of tuft withdrawal force and is applicable to all carpets with a cut or loop pile yarn structure.
2695
[Page extract]
ASTM C1147
ASTM C1147 testing covers the evaluation of joints between two pieces of weldable grades of thermoplastic material. This testing is intended to establish methods to evaluate minimum short term weld factors.
2696
[Page extract]
ISO 814
ISO 814 specifies a method for determining the adhesion strength of rubber-to-metal bonds where the rubber part is assembled between two parallel metal plates, using the adhesive system under investigation
2697
[Page extract]
Puncture/penetration jigs
Puncture tests are performed to determine the resistance of a material to a sharp or blunt object passing right through it. As such, they normally require the measurement of a peak load.
2698
[Page extract]
ASTM D2633
ASTM D2633 test methods cover procedures for the testing of thermoplastic insulations and jackets used on insulated wire and cable.
2699
[Page extract]
ASTM D5450/D5450M-11
This test method determines the transverse tensile properties of wound polymer matrix composites reinforced by high-modulus continuous fibers.
2700
[Page extract]
BS EN 12814-6
BS EN 12814-6 is a low temperature tensile test method for testing welded joints of thermoplastics semi-finished products.