Search results
951
Case study
Test dei componenti del ventilatore e degli apparecchi di assistenza respiratoria
Requisiti Un ventilatore (respiratore) fornisce "ventilazione meccanica" spostando aria respirabile dentro e fuori i polmoni di pazienti incapaci di respirare sufficientemente bene senza aiuto.
952
[Page extract]
Why is the 135° peel test important?
Seal strength testing plays a vital role in packaging quality control.
953
[Page extract]
Case studies and examples
In timber engineering, laminated beam testing revealed that one adhesive consistently produced substrate failures, showing a stronger bond than the timber itself.
954
[Page extract]
Applications of torque testing in packaging
Food and beverage: PET bottles, screw-top jars
Pharmaceutical: Child-resistant packaging, blister packs
Personal care: Tubes, pump dispensers
Chemical produc
955
[Page extract]
Applications of torque testing in packaging
Food and beverage: PET bottles, screw-top jars
Pharmaceutical: Child-resistant packaging, blister packs
Personal care: Tubes, pump dispensers
Chemical products: Industrial containers, tamper-evident closures
956
[Page extract]
Standards for bulk analysis testing
Applicable standards and protocols
To ensure consistency and regulatory compliance, bulk testing is often carried out in accordance with established standards. These include:
957
[Page extract]
How is the trapezoidal tear test performed?
A standard trapezoidal tear test follows a consistent sequence:
958
[Page extract]
The concentric ring method
The most widely used approach to equibiaxial flexure compression testing is the concentric ring method. A circular specimen is supported on an outer ring and loaded through a smaller, concentric inner ring.
959
[Page extract]
Speak to an Expert
The Concora Crush Test, as defined in TAPPI T 824, is a critical step in corrugated medium evaluation.
960
[Page extract]
Why choose Mecmesin for Delft tear testing
Standards-compliant precision
Mecmesin tensile testers are fully compatible with ISO 34-2, delivering accu
961
[Page extract]
Introduzione
La norma ISO 11040-4 Allegato F definisce il metodo standardizzato per testare le proprietà meccaniche delle siringhe preriempite, con particolare attenzione alla penetrazione e alla resistenza dell'ago.
962
[Page extract]
Why choose Mecmesin for needle penetration testing
Standards-ready testing equipment
Mecmesin systems meet the requirements of ASTM F2878, ISO 7864, and ASTM F2132.
963
[Page extract]
Industry applications
Medical devices - Sterile packaging and protective barriers must resist both penetration and puncture to maintain sterility and patient safety.
Construction - Roofing membranes, concrete, and floor unde
964
[Page extract]
Standards and regulations in shear testing
Several industry standards and protocols govern food shear testing, ensuring repeatable results and regulatory compliance. Examples include:
965
[Page extract]
Key mechanical testing methods
Short span compression testing differs from conventional compression tests because it uses a minimal support length to eliminate bending effects.
966
[Page extract]
Introduction
ISO 11040-4 Annex F outlines the standardized method for testing the mechanical properties of pre-filled syringes, specifically focusing on needle penetration and drag.
967
[Page extract]
FAQs about Ultimate Tensile Strength
What is ultimate tensile strength?
Ultimate tensile strength (UTS) is the highest amount of tensile stress a material can resist before it breaks.
968
[Page extract]
Why Mecmesin?
Mecmesin's testing systems offer the flexibility and precision needed for accurate lap shear testing under compression. Our solutions are:
969
[Page extract]
Applications in advanced ceramics and composites
Four-point bend testing is the preferred approach for assessing the flexural strength of advanced ceramics<
971
[Page extract]
What is the trapezoidal tear test?
The trapezoidal tear test is a mechanical method used to determine the tear strength of flexible sheet materials.
972
[Page extract]
Industry applications of tension testing
Manufacturing and product development
In engineering and manufacturing, tension testing verifies the performance of raw materials, components and finished products.
973
[Page extract]
Test method and procedure
Preparing specimens
Material selection - Use representative samples from the batch being tested.
Cutting - Prepare specimens to the exact dimensions specified in
974
[Page extract]
Grab method vs strip method
Compared with the strip method (as defined by ISO 13934-1), which grips the full width of the fabric, the grab method
975
[Page extract]
How is double lap shear testing performed?
Specimen preparation
Specimens are prepared according to standardised dimensions.