Search results
2851
[Page extract]
ASTM D6713-14
Materials shall be tested and the individual grades shall conform to specified values of the physical properties such as tensile strength, tensile elongation, tensile modulus, dimensional stability, flexural modulus, and Izod impact; and dimensional pro
2852
[Page extract]
ASTM D1414
ASTM D1414 is used to measure the mechanical properties of vulcanized rubber o-rings. Mecmesin test equipment is relevant to the tensile testing part of this standard, which covers a variety of different tests.
2853
[Page extract]
ASTM D6117-18
ASTM D6117 covers the evaluation of fastener use with “as manufactured” plastic lumber and shapes through the use of two different testing procedures:
2854
[Page extract]
ISO 20344
This Standard specifies methods for testing footwear designed as personal protective equipment.
8 groups of tests from dimensions to mechanical properties and fluid resistance.
Supplemented by ISO 20345
2855
Event
Tensile Testing: Basics, Tips, & Trends
Have you ever wondered if the seatbelt in your vehicle is strong enough to restrain you in a collision? How about the average person pulling the cork out of a wine bottle?
2856
Event
Materials Testing: Theory and Practice Pt. 1 & 2
Materials testing is often the last step in the manufacturing process. Yet, quality is the result of both the process and the material. If the material that goes into the product is inadequate or defective, then the product may be deficient or faulty.
2857
[Page extract]
BS EN 14477
Packaging, Packaging materials, Flexible materials, Perforating tests, Mechanical testing
2858
[Page extract]
ASTM E8/E8M-13a
These test methods cover the tension testing of metallic materials in any form at room temperature, specifically, the methods of determination of yield strength, yield point elongation, tensile strength, elongation, and reduction of area.
2859
[Page extract]
BS EN 319
EN319 specifies a method for determining the resistance to tension perpendicular to the plane of the board (“internal bond”) of particleboards, fibreboards, and cement-bonded particleboards.
2860
[Page extract]
TAPPI T 284
This test evaluates the ability of corrugating medium to contribute to the compression strenght of a corrugated box.
2861
[Page extract]
TAPPI T 549
This method describes a horizontal plane procedure for the determination of the coefficient of static and kinetic friction of paper measured when sliding against itself.
2862
[Page extract]
BS EN 12346
Gymnastics equipment, Wall bars, Ladders, Sports equipment, Indoor sports equipment, Design, Dimensions, Height, Dimensional tolerances, Shape, Strength of materials, Safety measures, Marking, Instructions for use, Equipment safety, Mechanical testing,
2863
[Page extract]
BS EN 2307
Ropes, Fibre ropes, Mechanical testing, Tensile testing, Dimensional measurement, Rope pitch, Elongation, Breaking load, Physical testing, Water-resistance tests, Mass, Linear density, Density measurement
2864
Event
Makers Hackathon, June 16-18th 2022, Malmö, Sweden
Who should attend?
Quality Managers, design/product engineers and materials specialist.
What is the exhibition about?
2865
Specials
Thermal cabinet environment chamber
Environmental chamber capability
Mecmesin's OmniTest twin column range can accommodate an environmental chamber to test materials in controlled ambient conditions.
2866
[Page extract]
ASTM D3330
These test methods cover the measurement of the peel adhesion of single and double-sided pressure-sensitive tapes.
2867
[Page extract]
ASTM D5672-09
This test method covers a screening type quality control test used to determine if flexible polyurethane foam cushions are within the specified grade range for firmness.
2868
[Page extract]
ASTM D3044
This test method covers determination of the shear modulus of wood-based structural panels associated with shear distortion in the plane of the panels. The method is applicable to all types of wood-based structural panels.
2869
[Page extract]
ASTM D3658
This test method covers the simplistic comparison of strengths of glass/metal joints when the adhesive is cured by ultraviolet (UV) radiation and standard specimens are used and tested under specified conditions of preparation, radiation, and load.
2870
[Page extract]
ASTM D7834-13
During the application of coatings, paint brushes can exhibit shedding of filling material onto the coated surface. A measure of this shedding filling material will determine the paint brush’s ability to resist shedding during application.
2871
[Page extract]
BS EN ISO 3376
This International Standard specifies a method for determining the tensile strength , elongation at a specified load and elongation at break. It is applicable to all types of leather
2872
[Page extract]
ASTM C1028
This test method covers the measurement of static coefficient of friction of ceramic tile or other surfaces under both wet and dry conditions while utilizing Neolite heel assemblies. This test method can be used in the laboratory or in the field.
2873
[Page extract]
AEC Q200-005
This specification establishes the procedure and criteria to determine the ability of surface
mounted device terminations and seals to withstand bending, flexing and pulling forces which
2874
[Page extract]
ASTM D7264 / D7264M-15
ASTM D7264 is a test method used to determine the flexural stiffness and strength properties of polymer matrix composites. The test method summarises two procedures:
2875
[Page extract]
ASTM F1473-18
ASTM F1473 is a test method determines the resistance of polyethylene materials to slow crack growth. It is also known as PENT (Pennsylvania Notch Test) test.