Search results
1476
[Page extract]
MIL 22520-G
This specification covers the general requirements for crimping tools, accessories and inspection gages used for connecting removable contacts (such as; signal, power, coaxial, shielded, thermocouple, and filter pin contacts) coaxial connectors, shielde
1477
[Page extract]
IEC 61210
IEC 61210:2010 applies to non-insulated flat quick-connect terminations consisting of a male tab of size 2,8 mm, 4,8 mm, 6,3 mm or 9,5 mm with hole or dimple detents and a mating female connector for use as either an incorporated or an integrated part o
1479
Bundle
Catalyst tester for ASTM D4179 and ASTM D6175
OmniTest 2.5
BD002
Catalyst crush strength tester, configured for key international test standards including ASTM D4179 and ASTM D6175.
1480
[Page extract]
ASTM D5766 / D5766-M
ASTM D5766 is a test method to determine the open-hole tensile strength of multidirectional polymer matrix composite laminates reinforced by high-modulus fibres.
1481
[Page extract]
ASTM D3470
This test method covers the determination of the force required to cause a downward-force-while-turning lug-finish closure to be rotated across the container finish lugs (strippage) without downward force being applied to the closure (Type IIA closures)
1484
[Page extract]
BS EN ISO 844
ISO 844 specifies a method of determining a) the compressive strength and corresponding relative deformation, or b) the compressive stress at 10 % relative deformation, and c) when desired, the compressive modulus of rigid cellular plastics.
1485
Event
WestPack Expo 2025
Lansmont - together with our sister brand Mecmesin - will be participating in the upcoming WestPack trade show!
1486
[Page extract]
Sistemi di forza
Hai bisogno di un livello di precisione e ripetibilità che non può essere raggiunto dai tester manuali?
1487
[Page extract]
ASTM F2878-10
This test method is used for determining the force required to cause a hypodermic needle to penetrate through protective clothing material.
1488
[Page extract]
SAE USCAR-21-4
This specification defines test methods and requirements for validation of solderless crimped connections.
1489
[Page extract]
ASTM E1820-18ae1
The ASTM E1820 test method covers procedures and guidelines for the determination of fracture toughness of metallic materials using the following parameters: K, J, and CTOD (δ). Toughness can be measured in the R-curve format or as a point value.
1491
[Page extract]
ASTM D1578
Significance and Use
Test Method D1578 for testing any spun yarn for breaking strength is considered satisfactory for acceptance testing of commercial shipments since the method has been used extensively in the trade.
1492
[Page extract]
ASTM C297
This test method determines the flatwise tensile strength of the core, the core-to-facing bond, or the facing of an assembled sandwich panel.
1493
[Page extract]
BS EN ISO 376
BS EN ISO 376:2011 looks at the calibration of force-proving instruments used for the static verification of uniaxial testing equipment. These include tension and compression testing machines.
1494
Event
180 Peel Testing Webinar (9 Feb. 2022)
Across many households and industries, consumers have developed a strong preference for and confidence in ‘Duct Tape’ for all types of uses and applications. This is mainly due to the adhesion strength.
1495
Event
Introduction to Consumer Packaging Testing
Damaged packaging can not only cost money but also impact brand perception. Consumers are less likely to purchase a product with damaged packaging, or if their product arrives damaged from poor packaging during the shipping and transport process.
1496
[Page extract]
Jewellery & Watch
In jewellery and watch production, alloys, components and other materials must meet the needs of the manufacturing process and the end-product should give good service performance when worn by the customer.
1497
[Page extract]
Why Mecmesin for pull-off and pull-out testing
Mecmesin designs and manufactures tensile and adhesion testing equipment for both destructive and non-destructive pull-off and pull-out applications.
1498
[Page extract]
Case studies and practical applications
Screw-cap torque test on PET bottles
A beverage manufacturer identified inconsistencies in bridge torque linked to capping machine variability.
1499
[Page extract]
Why is the 135° peel test important?
Seal strength testing plays a vital role in packaging quality control.
1500
[Page extract]
Standards for compressive hardness testing
Internationally recognised standards ensure that compressive hardness tests are accurate, repeatable, and comparable.