Search results
2951
[Page extract]
ASTM D6713-14
Materials shall be tested and the individual grades shall conform to specified values of the physical properties such as tensile strength, tensile elongation, tensile modulus, dimensional stability, flexural modulus, and Izod impact; and dimensional pro
2952
[Page extract]
BS 5081-1
A mechanical testing machine is used to move the syringe plunger and to aspirate and expel water, whilst the force exerted and the plunger travel are recorded.
2953
[Page extract]
ASTM D6117-18
ASTM D6117 covers the evaluation of fastener use with “as manufactured” plastic lumber and shapes through the use of two different testing procedures:
2954
[Page extract]
ASTM D2653
ASTM D2653 determines the tensile properties of elastomeric yarns made from natural rubber, spandex or other elastomers.
2955
[Page extract]
TAPPI T 810
This method describes a procedure for measuring the bursting strength of single wall and double wall corrugated board within the range of 690 kPa (100psi) to 4825 kPa (700 psi) employing an instrument which uses a disk shaped, molded diaphragm.
2956
[Page extract]
DIN EN 61238-1
Electric connectors, Crimped connectors, Electric cables, Power cables, Electric conductors, Electric wires, Copper, Aluminium, Temperature, Classification systems, Type testing, Short-circuit current tests, Resistance measurement, Mechanical testing, T
2957
[Page extract]
ASTM D3807
ASTM D3807 is a test method used to determine the strength properties of adhesives in cleavage peel by tension loading. It allows the comparative testing of cleavage/peel strengths of bonded engineering thermoplastic adherends.
2958
[Page extract]
ISO 188
ISO 188:2011 specifies accelerated ageing or heat resistance tests on vulcanized or thermoplastic rubbers. Two methods are given:
2959
[Page extract]
BS EN 671-1
Fire hydrants, Fire hoses, Firefighting equipment, Flexible pipes, Fire hose reels, Hose reels, Fire safety in buildings, Performance, Approval testing, Corrosion tests, Ageing tests, Flow measurement, Endurance testing, Impact testing, Pressure testing
2960
[Page extract]
BS EN ISO 10619-1
BS EN ISO 10619-1 is a test method covering bending tests on rubber or plastics hoses and tubing.
2961
[Page extract]
GS1 5.0
The Hanger Specifications are intended to increase efficiency in the supplier-to-retailer pipeline by minimizing order-to-sales floor cycle time.
2962
[Page extract]
TAPPI T 549
This method describes a horizontal plane procedure for the determination of the coefficient of static and kinetic friction of paper measured when sliding against itself.
2963
[Page extract]
BS EN 12562
Synthetic fibres, Polyamide fibres, Aramide fibres, Textile products, Textile testing, Yarn, Filament yarns, Filaments, Filament (textile fibre), Yarn testing, Yarn linear density determination, Elongation at fracture, Elongation, Force measurement, Mec
2964
[Page extract]
BS EN 12568
Protective footwear, Protective clothing, Toe-caps, Metals, Non-metals, Impact strength, Performance testing, Dimensions, Length, Impact testing, Compression testing, Penetration tests, Corrosion resistance, Corrosion tests, Bend testing, Marking, Test
2965
[Page extract]
ASTM D2718
These test methods determine the shear properties of structural panels associated with shear distortion of the planes parallel to the edge planes of the panels. Both shear strength and modulus of rigidity may be determined.
2966
[Page extract]
ISO 1924-1
Applies, within the limitations of the instruments used, to all papers and boards with the exception of corrugated board, but may be applied to the components of such board. Specifies the method which causes failure of the piece in a mean time of 20 s.
2967
Test Frame
Telaio di prova Vortex-dv
Telaio per test Vortex Un robusto telaio di prova a doppia colonna in grado di applicare una coppia fino a 10 Nm (90 lbf.in). Alto e largo abbastanza da accettare una varietà di campioni di prova ma compatto da usare come tester da banco. Visualizza il…
2968
[Page extract]
ASTM D4482-11
ASTM D4482 is a test method used to determine the fatigue life of rubber compounds undergoing a tensile-strain cycle. During part of the cycle, the strain is relaxed to a zero value.
2969
Event
Materials Testing: Theory and Practice Pt. 2
Materials testing is often the last step in the manufacturing process. Yet, quality is the result of both the process and the material. If the material that goes into the product is inadequate or defective, then the product may be deficient or faulty.
2970
[Page extract]
ASTM D7834-13
During the application of coatings, paint brushes can exhibit shedding of filling material onto the coated surface. A measure of this shedding filling material will determine the paint brush’s ability to resist shedding during application.
2971
[Page extract]
ASTM D143
These test methods cover the determination of various strength and related properties of wood by testing small clear specimens.
2972
[Page extract]
Afera 5001
Self Adhesive Tapes - Measurement of Peel Adhesion from Stainless Steel or from its own Backing.
2973
Event
Materials Testing: Theory and Practice Pt. 1
Materials testing is often the last step in the manufacturing process. Yet, quality is the result of both the process and the material. If the material that goes into the product is inadequate or defective, then the product may be deficient or faulty.
2974
[Page extract]
ASTM D7264 / D7264M-15
ASTM D7264 is a test method used to determine the flexural stiffness and strength properties of polymer matrix composites. The test method summarises two procedures: