Search results
1152
Case study
Hot air balloon cloth tensile strength and tear-resistance testing
Requirement
Ultramagic is the second largest hot air balloon manufacturer in the world.
For obvious safety reasons, the material used must conform to strict standards applicable to the aeronautical industry.
1153
[Page extract]
BS 6319-2
BS 6319-2 is a test method for determining the compressive strength of resin and polymer/cement compositions used in construction.
1154
[Page extract]
ASTM D3826
ASTM D3826 is a tensile test method, which covers a degradation-end point, or a brittle point) for degradable polyethylene/polypropylene films and sheeting less than 1.0 mm thick.
1155
Sensor
Sensors - Universal Testers (ELS)
Sensors
The OmniTest universal testers use Mecmesin's range of high-resolution precision Enhanced Load Sensors (ELS) to record tensile and compressive loads.
ELSA precision loadcell connects directly to an OmniTest or MultiTest-dV stand and communicates…
1156
[Page extract]
BS EN 12814-3
BS EN 12814-3 is a tensile creep test method for testing welded joints of thermoplastics semi-finished products.
1157
Page
Catalogo accessori
Scegli i tuoi accessori Per ottenere risultati accurati dei test, è importante che il campione sia afferrato e tenuto correttamente.
1158
[Page extract]
Support
Our sales, engineering and technical support teams are committed to providing the highest level of customer service. Mecmesin provide application and technical support for all of our products.
1159
[Page extract]
BS ISO 11752
BS ISO 11752 is a test method for determining the compressibility of flexible cellular polymeric materials.
1160
[Page extract]
BS 7320
This British Standard specifies requirements for sharps containers intended to hold potentially infectious medical waste comprised largely of devices which can readily cause physical injury e.g. scalpel blades, hypodermic needles and syringes.
1161
[Page extract]
CETIE Guide 1
This guideline applies to the capping of still wines with a cork mouth finish as per CETIE data sheet GME 50.01 which has been used as a base for the European standard EN 12726. Contains reference to 'extraction force', 'cork dimensional recovery', 'ch
1162
Case study
Headset microphone joint torque
Requirement
Jabra is a subsidiary of GN Netcom and is a global manufacturer of innovative headsets (wireless and corded) and speakerphone solutions.
1163
Case study
Top-load testing PET bottles
Requirement
Esterform Packaging manufacture more than a million PET bottles and preforms per day for major processors of bottled water, juices, soft drinks, dairy and household products.
1164
[Page extract]
ASTM D3410 / D3410M
ASTM D3410 determines the compressive properties of polymer matrix composite materials reinforced by high-modulus fibers.
1165
[Page extract]
BS EN ISO 12230
This European Standard specifies a method for the determination of the tensile properties of materials used as surfaces for sports areas.
1166
[Page extract]
ASTM D4776 / D4776M-18
ASTM D4776 is a test method used to determine the maximum adhesion force of tyre cords in rubber compounds.
1167
Case study
Synthetic sports surface tuft binding
Customised engineering example
Test method standard BS ISO 4919 applies to the tuft withdrawal force of carpets.
1168
[Page extract]
ASTM D6117-18
ASTM D6117 covers the evaluation of fastener use with “as manufactured” plastic lumber and shapes through the use of two different testing procedures:
1169
Case study
Medical sharps bin puncture resistance
Customised engineering example
International standards (ASTM F2132, BS 7320, BS 23907) specify the puncture resistance of medical sharps containers.
1170
[Page extract]
ASTM D876 - 13
ASTM D876 is a test method covering the testing of general-purpose (Grade A), low-temperature (Grade B), and high-temperature (Grade C)2 non-rigid vinyl chloride polymer tubing, or its copolymers with other materials, for use as electrical insulation.
1171
[Page extract]
UL 486A-B
UL 486A-B is a safety standard that outlines the requirements for wire connectors and soldering lugs used with electrical conductors.
1172
[Page extract]
ASTM D3469
These test methods measure the downward forces during the disengagement of lug-style caps from their respective containers. The methods measure the maximum torque developed while the cap is further disengaged by turning of the container.
1173
Case study
Grenade cartridge sheath projectile separation pull testing
Requirement
When manufacturing ammunition, the projectile is set into the case and it is crimped or sealed in place.
1174
Sensor
Sensors - Helixa
Torque sensors
The HTC range of interchangeable torque sensors are specially adapted for the Helixa test system. Plug and play for automatic calibration with availability to suit all requirements in capacities from 0.1 N.m (0.9 lbf.in) to 6 N.m (50 lbf.in…
1175
[Page extract]
ASTM D6068-10
This test method covers the determination of the J-integral versus crack growth resistance (J-R) curves for polymeric materials.