Search results
1001
Bundle
ASTM F88 seal strength tester
OmniTest 2.5
BDO25
ASTM F88 covers the measurement of the strength of seals in flexible barrier materials.
1002
[Page extract]
ISO 2439
The indentation hardness of flexible cellular materials is a measure of their load-bearing properties.
1003
Event
Tensile Testing: Pull Force & Break Strength
Whether it is medical tubing, plastic straws, copper wire or zip ties, pull force and break strength testing is critical not only to production quality but also to consumer safety.
1004
[Page extract]
BS EN 12209
BS EN 12209:2016 specifies requirements and test methods for the durability, strength, security, and function of mechanically operated locks and latches and their locking plates for use in doors, window doors and entrance doors in buildings.
1005
[Page extract]
BS EN 1464
Specifies a floating roller method for the determination of the peel resistance of adhesive bonds between one rigid adherend and one flexible adherend when tested under specified conditions of preparation and testing.
1006
Event
Medical Devices: General testing with 21 CFR Part 11 compliance
Reliable results, trusted compliance: 21 CFR Part 11's role in securing medical device quality testing.
Quality testing of Medical Devices ranges from syringe actuation (break loose and glide), needle sharpness and adhesion strength to Child R
1007
[Page extract]
What is tension testing?
Tension testing, also called tensile testing, is a core mechanical test used to determine how a material behaves when subjected to a uniaxial tensile force. It measures properties such as strength, ductility and elasticity under controlled conditions.
1008
[Page extract]
ASTM D6415 / D6415M-06a
ASTM D6415 is designed to measure the curved beam strength properties of fiber reinforced composites using a 90˚ curved beam specimen. The curved beam strength represents the moment per unit width which causes a delamination to form.
1009
[Page extract]
ISO 10354
Simulates in a qualitative manner the forces and effects on an adhesive-bonded joint at a metal-adhesive/primer interface. It can also be used as a method of checking the surface preparation of substrates.
1010
[Page extract]
SAE USCAR-21-4
This specification defines test methods and requirements for validation of solderless crimped connections.
1011
[Page extract]
BS ISO 7743
ISO 7743 specifies methods for the determination of the compression stress-strain properties of vulcanized or thermoplastic rubber using a standard test piece, a product or a part of a product.
Four procedures are given:
1012
Page
Contact sales
Looking for the right testing solution?
Our experts are ready to help - just complete the form below and one of our Technical Sales Engineers will be in touch.
1013
[Page extract]
ISO 1926
ISO 1926 specifies a method of determining the behaviour of rigid cellular plastics materials when they are subjected to a tensile stress.
1014
Case study
Stabilised spring testing
Customised engineering example
Our client needed to test a number of small, lightweight springs under compression. To avoid buckling and sideways movement of the springs, a supporting spindle or guide-rod was required.
1015
[Page extract]
ASTM C1147
ASTM C1147 testing covers the evaluation of joints between two pieces of weldable grades of thermoplastic material. This testing is intended to establish methods to evaluate minimum short term weld factors.
1016
[Page extract]
TAPPI T 825
The flat crush test (1) is a measure of the resistance of the flutes in corrugated board to a crushing force applied perpendicular to the surface of the board under prescribed conditions.
1017
[Page extract]
Force systems
Do you need a level of accuracy and repeatability which just cannot be achieved by manual testers?
1018
Event
Pull Force and Break Strength Testing
Whether it is medical tubing, plastic straws, copper wire or zip ties, pull force and break strength testing is critical not only to production quality but also to consumer safety.
1019
[Page extract]
Bulk analysis
In industries where powders, granules or pelletised materials are formulated, processed or packaged, maintaining consistency in texture and perf
1020
[Page extract]
Compression
Compression testing is a way of determining how something will react when a compressive force is applied to it. It typically involves measuring the relationship between the applied force and how much the object deforms.
It is performed to:
1021
Sensor
Sensors - Universal Testers (ELS)
Sensors
The OmniTest universal testers use Mecmesin's range of high-resolution precision Enhanced Load Sensors (ELS) to record tensile and compressive loads.
ELSA precision loadcell connects directly to an OmniTest or MultiTest-dV stand and communicates…
1022
[Page extract]
What is the edge crush test and why is it important?
ECT assesses the capacity of corrugated board to withstand compressive forces along its edge. A higher ECT value generally means the board has greater stacking strength.
1023
[Page extract]
Jewellery & Watch
In jewellery and watch production, alloys, components and other materials must meet the needs of the manufacturing process and the end-product should give good service performance when worn by the customer.
1024
Accessory
Miniature Vice Grip, 100 N, QC-20 fitting
MecS341
Versatile, easy to use, and suitable for small components (eg bonded joints) where access is limited and tensile forces are below 100 N.
Clamping surfaces are machined with pyramid-shaped serrations to ensure optimum gripping force.
The flexible chain-…
1025
Accessory
Compression Plate, Self-levelling, Hardened & Ground, 70 mm, 5-16 UNC
432-350
Self-levelling compression plates are ideal for general compression testing on a range of materials and finished products. Self-levelling allows parallelism to be set for those applications where it is critical to accurately measure the deformation of a…