Search results
2501
[Page extract]
ASTM F1995-12
This test method covers the determination of the shear integrity of materials and procedures used to attach surface mount devices (SMD) to a membrane switch circuit.
2502
[Page extract]
*corp Ford DSEU
Test method covering measurement of door slam energy for Ford Chenai, India. Shows Mecmesin loadcell, display and special gripping fixtures. Note: Diagram shows a rigid link bar, which was later replaced by a flexible bungee connection.
2503
[Page extract]
ISO 8094
ISO 8094 specifies a test method for determining the adhesion strength of the cover to the core layer. It applies exclusively to steel cord conveyor belts.
2504
[Page extract]
ASTM D1708
ASTM D1708 is used to determine the tensile and elongation properties of small plastic microtensile specimens. These plastic specimens can be of any thickness up to 3.2 mm (1/8 in), including thin films. This test method does not require the use of an
2505
[Page extract]
BS 6319-6
BS 6319-6 is a test method for determining the modulus of elasticity in compression of resin and polymer/cement compositions for use in construction.
2506
[Page extract]
BS ISO 7322
This International Standard specifies test methods for the determination of the following characteristics of composition cork (= product obtained from the agglutination of cork granules with the addition of a binder generally not derived from cork cells
2507
[Page extract]
ASTM D378
The ASTM D378 test method is used for evaluating the physical properties of flat conveyor belting, which are used in many industrial applications in which they are subjected to a great variety of stresses and conditions.
2508
[Page extract]
ISO 8510-2
Specifies a 180° peel test for the determination, under specified conditions, of the peel resistance of a bonded assembly of two adherends where one adherend is flexible and the other is rigid.
2509
[Page extract]
ASTM D4476 / D4476M-14
ASTM D4476 is a test method used to determine the flexural properties of fiber-reinforced pultruded plastic rods. The specimen used is a rod with a semi-circular cross section, moulded or cut from lengths of pultruded rods.
2510
[Page extract]
ISO 15509
Gives a test method for measuring the shear and/or tensile strength of an adhesively bonded plastic/plastic specimen of a specific design. This method allows the determination of a combined shear and tensile behaviour of the bond.
2511
[Page extract]
BS EN ISO 10066
BS EN ISO 10066 is a test method for determining creep in tension of flexible cellular polymeric materials.
2512
[Page extract]
SAE J 1553
This SAE Recommended Practice describes a cross peel test method for use in measuring the bonding characteristics of automotive-type adhesives for joining fiber-reinforced plastics to themselves and to metals.
2513
[Page extract]
TAPPI T 840
This method describes a procedure for evaluating the adhesive used in glued lap joints of corrugated containers.
2514
[Page extract]
BS EN ISO 12230
This European Standard specifies a method for the determination of the tensile properties of materials used as surfaces for sports areas.
2515
[Page extract]
BS EN 868-5
Provides examples of particular requirements and test methods for heat and self-sealable pouches and reels manufactured from paper complying with EN 868-3 and plastic film complying with clause 4 of this European standard.
2516
[Page extract]
ASTM E855-08
This standard describes three test methods for determining the modulus of elasticity in bending and the bending strength of metallic strips or sheets intended for the use in flat springs.
2517
[Page extract]
CETIE Guide 2
This guide applies to the screw capping of non-carbonated beverages and products with a metallic tamper-evident closure. Bottles may also be fitted with an in-bore insert for product flow control or to prevent re-filling.
2518
[Page extract]
ASTM D6004-04
This test method describes a procedure to measure shear strength development for adhesives used to bond carpet adhesives to selected underlayments.
2519
[Page extract]
BS EN ISO 10074
Aluminium, Aluminium alloys, Coated materials, Anodizing, Anodic coating, Coatings, Thickness, Density, Surface defects, Classification systems, Oxides, Inspection, Grades (quality), Wear resistance, Hardness, Corrosion resistance, Wear tests, Specimen
2520
Article/Campaign
Test title
Top-load testing solutions
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Fusce ac ipsum varius, porttitor enim eu, porta ipsum. Quisque fermentum dolor est, in interdum purus tincidunt vitae.
2521
[Page extract]
ASTM F2256-05
This test method is intended to provide a means for comparison of the adhesive strengths of tissue adhesives intended for use as surgical adhesives or sealants, or both, on soft tissue.
2522
[Page extract]
ASTM D5458-95
This test method measures cling between two layers of film, in both a stretched and unstretched condition.
2523
[Page extract]
ASTM D3846
ASTM D3486 is a test method used for evaluating the in-plane strength of reinforced thermosetting plastics in flat sheet form in thicknesses ranging from 2.54 to 6.60 mm.
2524
[Page extract]
ASTM D5649-01
This test method is used to make comparative assessments of the securing or locking effect of adhesives used in threaded assemblies.
2525
[Page extract]
ISO 9727-4
ISO 9727-4 specifies a test method for determining the percentage of diameter recovery of cylindrical cork stoppers, after compression.