Search results
1426
[Page extract]
ASTM D3575
ASTM D3575 covers a number of tests for determining properties of polyethylene foams including compressive strength.
1427
[Page extract]
ASTM D6175-03
5.1 This test method is intended to provide information on the ability of an extruded catalyst to retain physical integrity during use.
1428
[Page extract]
ASTM D3658
This test method covers the simplistic comparison of strengths of glass/metal joints when the adhesive is cured by ultraviolet (UV) radiation and standard specimens are used and tested under specified conditions of preparation, radiation, and load.
1429
[Page extract]
BS EN 681-1
This standard specifies requirements for materials used in vulcanized rubber seals for:
1) cold potable water supply (up to 50®C);
1430
[Page extract]
ISO 374-4
This document specifies the test method for the determination of the resistance of protective glove materials to degradation by dangerous chemicals with continuous contact.
1431
[Page extract]
ASTM D6742 / D6742M
ASTM D6742 is the standard test method for tensile and compression testing of filled-hole polymer matrix composite laminates. It provides instructions for modifying open-hole tension and compression test methods to determine filled-hole tensile and com
1432
[Page extract]
ISO 178
ISO 178 is a test method for the determination of flexural properties of rigid and semi-rigid plastics. These properties include flexural modulus and flexural strength.
1433
[Page extract]
Special compression fixtures
Special compression fixtures have been specially designed to meet the challenges of a particular application.
1434
Event
Cap Closure and Removal Torque Testing
The primary objective for measuring and analyzing the torque characteristics of a container cap is to accurately determine not only the quality of the part or process, but also the root cause of a wide variety of defects.
1435
[Page extract]
ISO 34-2
ISO 34-2 specifies a method for the determination of the tear strength of small test pieces (Delft test pieces) of vulcanized or thermoplastic rubber.
1436
[Page extract]
BS EN 520
Plasterboard, Gypsum plaster, Boards, Wall linings, Construction systems parts, Performance, Strength of materials, Fire resistance, Sound insulation, Water vapour, Permeability, Thermal resistance, Performance testing, Dimensional measurement, Physical
1437
[Page extract]
ASTM D5528-13
ASTM D5528 is a test method, which determines the opening Mode I interlaminar fracture toughness of continuous fiber-reinforced composite materials. It uses a a double cantilever beam (DCB) specimen. Susceptibility to delamination is one of the major
1438
[Page extract]
BS 2782-12: 1210A to C
BS 2782-12: Method 1210A to C specifies a test method for testing the longitudinal tensile properties of glass-reinforced thermosetting plastics (GRP) pipes.
1439
Event
Essentials of Adhesion (Peel) Testing
There is a reason people reach for Duct Tape as a fix for almost everything – Adhesion Strength. From busted pipes to ripped furniture, the preference for a solution that “does not easily peel off” is the guiding principle for manufactures.
1440
[Page extract]
CETIE Guide 7 (FR)
Ce guide concerne le bouchage à vis des vins tranquilles, avec une fermeture métallique avec insert plastique fileté et témoin de violabilité ou bande de garantie qui doit être déchiré à l’ouverture.
1442
[Page extract]
BS EN 12814-1
BS EN 12814-1 is a bend test method for testing welded joints of thermoplastics semi-finished products.
1443
[Page extract]
ASTM F1839-08
This specification covers rigid polyurethane foam blocks or sheets recommended for use as a standard material for mechanical testing using orthopedic devices and instruments.
1444
[Page extract]
BS EN 1394
BS EN 1394 is a tensile test method to determine the initial circumferential tensile strength of plastic pipes.
1445
[Page extract]
ANSI/EIA 364-38B
This standard establishes a test method to determine the axial tensile load that can be applied to a mated pair of connectors and the holding effect of a connector cable clamp without causing any detrimental effects upon the cable or connector when subj
1446
[Page extract]
BS EN ISO 14129
BS EN ISO 14129 is a test method used to determine the in-plane shear stress/shear strain response of fibre-reinforced plastic components.
1447
[Page extract]
GB/T 6548
Uses pin accessories, see linked file (which is not the standard) and compare TAPPI T821 om-12
A compression action to create tension between the layers.
1448
[Page extract]
ASTM D5169-98
This test method measures the shear strength of hook and loop touch fasteners using a recording constant rate of extension (CRE) tensile testing machine.
1449
[Page extract]
BS ISO 3384-1:2001+A1
BS ISO 3384-1 is a test method for determining the stress relaxation in compression of vulcanised rubber or thermoplastic.
1450
[Page extract]
ASTM D6195-03
These test methods cover the determination of properties of a pressure-sensitive adhesive. These test methods are applicable to those adhesives that form a bond of measurable strength rapidly upon contact with another surface.