Search results
226
Event
Fundamentals of Compression Testing
Push or compressive testing helps determine the limits of most products that require constant pushing or compression.
228
[Page extract]
ISO 34-1
ISO 34-1 measures tear strength test methods for rubber test samples. The test results in measurement of a materials resistance to tearing. Tear strength can also be used to monitor material anisotropy of a material.
229
[Page extract]
ASTM D937-97
1.1 This test method covers measuring with a penetrometer the penetration of petrolatum as an empirical measure of consistency.
230
[Page extract]
ASTM D4964-96
5.1 This test method for testing loop tension and elongation of elastic fabrics is considered satisfactory for acceptance testing of commercial shipments of elastic fabrics because the test method is used in the trade for acceptance testing.
231
Event
Fundamentals of Compression Testing
How much force is required to register a command when you click your computer mouse?
How much force can a water bottle take before it collapses in its case under a stack?
232
[Page extract]
BS EN 17394-2
This document defines a test method for security of attachment of functional and decorative buttons to clothing including garments such as gloves, hats, scarves, hosiery, ties, and textile belts. The scope of this document is limited to sewn-on buttons,
233
Event
Compression Testing in Top Load Applications
A typical challenge in packaging, and bottling applications is trying to balance product integrity, where the container might be too weak and crush under load, and excessive raw material cost, where the container is too strong.
234
[Page extract]
ASTM D790-17
ASTM D790 is used to determine the flexural properties of unreinforced and reinforced plastics, including high modulus composites and electrical insulating materials utilizing a three-point loading system to apply a load to a simply supported beam (spec
235
[Page extract]
BS 1726-1
Provides guidance on methods of specifying and tolerancing hot coiled compression springs, and cold coiled springs that fall outside the size range limits specified in BS EN 15800.
236
[Page extract]
SAE AIR 1471A
The purpose of this SAE Aerospace Information Report (AIR) is to provide the aerospace propulsion industry with recommended assembly torque limits for commonly used aircraft propulsion system threaded fasteners when a common torque value per fastener si
238
Event
Fundamentals of Compression Testing
How much force is required to register a command when you click your computer mouse?
How much force can a water bottle take before it collapses in its case under a stack?
239
Sensor
AFTI - Force sensors
Force sensors
The AFTI and AFG are versatile force and torque indicators designed for use with the Mecmesin range of 'Smart' tension and compression loadcells.
Readings are displayed as live values with peak-hold function in both tension and compression.…
240
[Page extract]
ASTM D751-06
These test methods cover, but are not limited to, rubber-coated fabrics, that is, tarpaulins, rainwear, and similar products.
241
[Page extract]
ISO 1924-1
Applies, within the limitations of the instruments used, to all papers and boards with the exception of corrugated board, but may be applied to the components of such board. Specifies the method which causes failure of the piece in a mean time of 20 s.
242
[Page extract]
BS EN 1270
Basketball equipment, Ball-games equipment, Sports equipment, Classification systems, Dimensions, Safety measures, Performance, Properties, Performance testing, Mechanical testing, Sports nets.
243
[Page extract]
ASTM D1578
Significance and Use
Test Method D1578 for testing any spun yarn for breaking strength is considered satisfactory for acceptance testing of commercial shipments since the method has been used extensively in the trade.
244
[Page extract]
ASTM E1012-12e1
It has been shown that bending stresses that inadvertently occur due to misalignment between the applied force and the specimen axes during the application of tensile and compressive forces can affect the test results.
245
[Page extract]
BS EN 12090
Thermal insulating materials, Thermal insulation, Construction materials, Shear testing, Shear strength, Shear stress, Specimen preparation, Formulae (mathematics), Test specimens, Test equipment, Testing conditions, Adhesives, Mechanical testing, Repor
246
[Page extract]
ASTM D6068-10
This test method covers the determination of the J-integral versus crack growth resistance (J-R) curves for polymeric materials.
248
Sensor
AFTI - Capteurs de force
Capteurs de force
L'afficheur AFTI et les dynamomètres AFG sont des indicateurs de force et de couple polyvalents conçus pour être utilisés avec la gamme de capteurs de force de traction et de compression «Smart» Mecmesin .
Les lectures sont affichées…
249
Sensor
VFTI - Force and Torque Sensors
Force and Torque sensors
The VFTI, AFTI, VFG and AFG are versatile force and torque indicators designed for use with the Mecmesin range of 'Smart' tension and compression loadcells and 'Smart' static and rotary torque sensors.
Readings are displayed as…
250
Sensor
VFTI - Capteurs de force et de couple
Capteurs de force et de couple Les VFTI, AFTI, VFG et AFG sont des afficheurs numériques de force et de couple très polyvalents et conçus pour utilisation avec la gamme Mecmesin de cellules de charge de traction et de compression « Smart » et de capteurs…