Search results
851
Case study
Railcar spring testing
Requirement
Seoul Metropolitan Railway Transit Corporation required a system for testing a variety of springs in their electric railcars. The springs range in size from 3mm to 100 mm in diameter.
852
[Page extract]
Applications across industries
Aerospace - testing honeycomb panels for aircraft interiors and structural assemblies.
Automotive<
853
[Page extract]
ASTM D3165
This test method is useful in that the joint configuration closely simulates the actual joint configuration of many bonded assemblies.
854
[Page extract]
ASTM C273/C273M
This test method is used to determine core shear properties of a sandwich construction material using loading plates bonded to the outer surfaces or skins (facesheets).
855
[Page extract]
BS EN ISO 9626
This International Standard specifies the dimensions, surface and mechanical properties of normal- and thin-walled tubing of designated metric sizes 3,4 mm to 0,3 mm, and of extra-thin-walled tubing of designated metric sizes 2,1 mm to 0,6 mm.
856
[Page extract]
BS EN ISO 8295
ISO 8295 specifies a method for determining the coefficients of starting and sliding friction of plastics film and sheeting when sliding over the same or other substances. It is intended to be used for non-sticky plastic film and sheeting of up to appr
857
[Page extract]
FINAT FTM3
This test method allows the end user to determine the force required to separate the release backing from the pressure sensitive adhesive coated face material.
858
[Page extract]
TAPPI T 818
The ring crush test correlates with edgewise compression strength of paperboard. This method is intended for paperbaord between 0.28mm (0.011 in.) and 0.51mm (0.020 in) thick.
859
Case study
Electrical assembly component strength
Customised engineering example
Due to the complex, asymmetric shapes of electrical assemblies, it can be difficult to grip the soldered, fused and welded parts in a way that mimic the forces applied when in use.
860
[Page extract]
TAPPI T 556
This procedure is used to measure the bending resistance of paper and paperboard in the machine and cross machine directions, by determining the bending resistance in mN of a 38mm (1.5in) wide vertically clamped sample, at 15o or 7.5o deflection.
861
[Page extract]
ASTM D1321
This test method covers the empirical estimation of the consistency of waxes derived from petroleum by measurement of the extent of penetration of a standard needle.
862
[Page extract]
Force systems
Do you need a level of accuracy and repeatability which just cannot be achieved by manual testers?
863
[Page extract]
ASTM D7834-13
During the application of coatings, paint brushes can exhibit shedding of filling material onto the coated surface. A measure of this shedding filling material will determine the paint brush’s ability to resist shedding during application.
864
[Page extract]
ISO 505
ISO 505 specifies a method of test for the measurement of the propagation resistance of an initial tear in textile conveyor belts, either in full thickness or of the carcass only.
865
[Page extract]
TAPPI T 284
This test evaluates the ability of corrugating medium to contribute to the compression strenght of a corrugated box.
866
Event
Understanding Adhesion Strength: 180 Degree Peel Test
Across many households and industries, consumers have developed a strong preference for and confidence in ‘Duct Tape’ for all types of uses and applications. This is mainly due to the adhesion strength.
867
Case study
End float test of inhaler cap
Requirement
'End float is the displacement in mm of a product', in this case the dispensing cap closure of the inhaler measured at a specific load.
868
Case study
Force de dépliage d'emballage en carton de bouteilles et de cannettes
Exemple d'ingénierie sur mesure
Un fabricant de cartons souhaitait tester de manière qualitative la force de déploiement de ses modèles, principalement utilisés pour emballer des bouteilles de boisson et des canettes.
869
[Page extract]
ASTM D747-10
ASTM D747 is used to determine the flexibility of plastics by means of a cantilever beam.
870
[Page extract]
Type d'essai
Mecmesin fournit des solutions pour des essais sur produits ou de matériaux nécessitant la mesure de leur résistance physique.
871
[Page extract]
BS EN ISO 205
Adhesives. Wood adhesives for non-structural applications. Determination of tensile shear strength of lap joints.
872
Case study
Test de mesure de couple sur fermeture de poubelle sanitaire
Exemple d'ingénierie sur mesure
Un fabricant de poubelles hygiéniques nous est arrivé avec une unité d’élimination des couches équipée d’un mécanisme d’admission rotatif.
873
Case study
Crimp testing cables
Requirement
A leading British cable assembly manufacturer, Telecom Connections Limited, who provide customers in the telecoms and electronics industries with quality cable assemblies and harnesses, wanted to test their wire crimp terminals to m
874
[Page extract]
ASTM D5868-01
Due to the increased use of adhesively-bonded FRP as a result of the inherent advantages afforded by bonded rather than mechanically-fastened joints (particularly the alleviation of stress risers and stress cracking), there is a need for tests by which
875
[Page extract]
ASTM D937-97
1.1 This test method covers measuring with a penetrometer the penetration of petrolatum as an empirical measure of consistency.