Search results
626
[Page extract]
ISO 7439
ISO 7439:2002 is applicable to single-use copper-bearing intra-uterine contraceptive devices and their insertion instruments.
627
[Page extract]
ASTM D1002
This test method covers the determination of the apparent shear strengths of adhesives for bonding metals when tested on a standard single-lap-joint specimen and under specified conditions of preparation and test.
628
[Page extract]
BS EN ISO 13934-1
Part 1 of ISO 13934 specifies a procedure to determine the maximum force and elongation at maximum force of textile fabrics using a strip method.
629
[Page extract]
*corp ITF TB 03/01
The official Rules of Tennis requires that any ball which is to be considered for use in any tournament which is played according to the Rules of Tennis, shall be named on the official list of balls which have been tested and approved as conforming to t
630
Event
Essentials of GRIP & FIXTURE Selection in Force & Torque Testing Webinar
When physically testing a material or component, the ability to apply load to a test specimen is important—but having the ability to apply that load correctly is just as crucial.
631
Product
Instrument d'essai de résistance du béton à 'jeune âge'
Pénétromètre à béton projeté
850-611
Le pénétromètre à béton projeté est un système complet et portable permettant de tester la résistance à la compression de la première étape de durcissement du béton frais pulvérisé (aussi nommé 'du béton à jeune âge') selon la norme BS EN 14488-…
632
Event
Essentials of grip & fixture selection in force & torque testing
For a test to work, the test system needs to properly interface with its specimen.
633
[Page extract]
ASTM D6272-17
This test method covers the determination of flexural properties of unreinforced and reinforced plastics, including high-modulus composites and electrical insulating materials in the form of rectangular bars molded directly or cut from sheets, plates, o
634
[Page extract]
ISO 16047
ISO 16047:2005 specifies the conditions for carrying out torque/clamp force tests on threaded fasteners and related parts.
635
Event
Fundamentals of Food Texture Analysis
The primary goal for using instrumentation to measure texture is to capture an objective value to something that is typically evaluated very subjectively. Texture cannot be controlled unless it measured in a consistent and repeatable manner.
636
Event
Fundamentals of Texture Testing Analysis
The primary goal for using instrumentation to measure texture is to capture an objective value to something that is typically evaluated very subjectively. Texture cannot be controlled unless it measured in a consistent and repeatable manner.
637
[Page extract]
TAPPI T 402
Standard conditioning and testing atmospheres for paper, board, pulp handsheets, and related products, Test Method TAPPI/ANSI T 402 sp-13
638
[Page extract]
EN 12089
Thermal insulating materials, Bend testing, Construction materials, Loading, Deflection tests, Mechanical testing, Testing conditions, Test equipment, Test specimens, Reports, Accuracy, Reproducibility.
639
[Page extract]
CETIE Guide 5
This document gives background information and recommended best practices for the application of plastic flat-top screw-on caps onto PET bottles for beverages. It covers all closure sizes and beverage product types.
640
[Page extract]
ISO 13939
Describes a method of comparing the performance test results of foil journal bearings, which are lubricated by air (gas) and supported by hydrodynamic force generated by the rotation of the rotating shaft.
641
[Page extract]
ISO 3781
Specifies a test method for the determination of the wet tensile strength of paper or board after its immersion in water for a specified period.
642
Event
Introduction to Consumer Packaging Testing
Damaged packaging can not only cost money but also impact brand perception. Consumers are less likely to purchase a product with damaged packaging, or if their product arrives damaged from poor packaging during the shipping and transport process.
643
Product
Perfect binding adhesive strength tester
Page Pull Tester
802-001+853-415
The Mecmesin 'Pira' Page Pull Tester is used in over 100 binderies across the world.
It provides a robust, economical and reproducible method of measuring the page pull strength of perfect-bound books.
By enabling an efficient binding endurance test, the…
644
[Page extract]
BS EN 13942
This International Standard specifies requirements and provides recommendations for the design, manufacturing, testing and documentation of ball, check, gate and plug valves for application in pipeline systems meeting the requirements of ISO 13623 for t
645
[Page extract]
ASTM D885/D885M-10a
These [comprehensive] test methods cover the testing of industrial filament yarns made wholly of manufactured organic-base fibers, cords twisted from such yarns, fabrics woven from such cords, and products that are made specifically for use in the manuf
646
Event
Automotive Component Torque Testing
This webinar will focus on the measurement of the torque resistance in knobs, switches, and torsion springs, which are among several components in automobiles that require testing to ensure quality, performance, and safety.
647
Case study
Police force manual handling and protective clothing
Requirement
A major UK police force requires all new recruits to pass a ‘Job Related Fitness Test’ (JRFT), to ensure they are able to meet the taxing physical demands of the role. Armed officers must undergo yearly re-assessment.
648
Event
Cork Pull & Cork Compression Testing OnDemand Webinar
FORCE TESTING in Wine & Spirit Applications
649
Case study
Solar panel peel testing
Requirement
A solar module, also called a PV or photovoltaic module and solar panel, is subjected to extreme conditions of temperature, ultraviolet radiation, rain, ice and wind throughout the year.
650
Case study
Test de résistance sur masque FFP1, FFP2 et FFP3
Exigence
Avec une production en Chine de plus de 200million de masques facials par jour - plus de 20 fois plus la quantité normale depuis le début Février - et en considérant que la plus part des nations ont décentralisées la production des pr