Search results
1001
Event
Tensile Testing: Pull Force & Break Strength
Whether it is medical tubing, plastic straws, copper wire or zip ties, pull force and break strength testing is critical not only to production quality but also to consumer safety.
1002
[Page extract]
ISO 10354
Simulates in a qualitative manner the forces and effects on an adhesive-bonded joint at a metal-adhesive/primer interface. It can also be used as a method of checking the surface preparation of substrates.
1003
Event
Medical Devices: General testing with 21 CFR Part 11 compliance
Reliable results, trusted compliance: 21 CFR Part 11's role in securing medical device quality testing.
Quality testing of Medical Devices ranges from syringe actuation (break loose and glide), needle sharpness and adhesion strength to Child R
1004
Caso de estudio
Stabilised spring testing
Customised engineering example
Our client needed to test a number of small, lightweight springs under compression. To avoid buckling and sideways movement of the springs, a supporting spindle or guide-rod was required.
1005
Página
Contact sales
Looking for the right testing solution?
Our experts are ready to help - just complete the form below and one of our Technical Sales Engineers will be in touch.
1006
[Page extract]
SAE USCAR-21-4
This specification defines test methods and requirements for validation of solderless crimped connections.
1007
[Page extract]
BS ISO 7743
ISO 7743 specifies methods for the determination of the compression stress-strain properties of vulcanized or thermoplastic rubber using a standard test piece, a product or a part of a product.
Four procedures are given:
1008
[Page extract]
ASTM C1147
ASTM C1147 testing covers the evaluation of joints between two pieces of weldable grades of thermoplastic material. This testing is intended to establish methods to evaluate minimum short term weld factors.
1009
[Page extract]
ISO 1926
ISO 1926 specifies a method of determining the behaviour of rigid cellular plastics materials when they are subjected to a tensile stress.
1010
[Page extract]
TAPPI T 825
The flat crush test (1) is a measure of the resistance of the flutes in corrugated board to a crushing force applied perpendicular to the surface of the board under prescribed conditions.
1011
[Page extract]
Force systems
Do you need a level of accuracy and repeatability which just cannot be achieved by manual testers?
1012
Event
Pull Force and Break Strength Testing
Whether it is medical tubing, plastic straws, copper wire or zip ties, pull force and break strength testing is critical not only to production quality but also to consumer safety.
1013
[Page extract]
Bulk analysis
In industries where powders, granules or pelletised materials are formulated, processed or packaged, maintaining consistency in texture and perf
1014
[Page extract]
Compression
Compression testing is a way of determining how something will react when a compressive force is applied to it. It typically involves measuring the relationship between the applied force and how much the object deforms.
It is performed to:
1015
Sensor
Sensors - Universal Testers (ELS)
Sensors
The OmniTest universal testers use Mecmesin's range of high-resolution precision Enhanced Load Sensors (ELS) to record tensile and compressive loads.
ELSA precision loadcell connects directly to an OmniTest or MultiTest-dV stand and communicates…
1016
[Page extract]
What is the edge crush test and why is it important?
ECT assesses the capacity of corrugated board to withstand compressive forces along its edge. A higher ECT value generally means the board has greater stacking strength.
1017
[Page extract]
Jewellery & Watch
In jewellery and watch production, alloys, components and other materials must meet the needs of the manufacturing process and the end-product should give good service performance when worn by the customer.
1018
Accesorio
Lightweight hanger and 5 N slotted mass for verifying FPT 10 N
432-655
A lightweight hanger and an M1 slotted mass of 5N.
For use with the FPT-H1 loadcell calibration checking kit (432-635) to verify the accuracy of HILC 10 N loadcells.
1019
Accesorio
Charger for digital gauges, UK, 230 V, 3-pin square
304-005
For use with Mecmesin digital force and torque gauges. 230 Volt with 3 square pins. Commonly used in the UK.
The mains adaptor/charger is a constant-current type:
Primary circuit: 230V – 50Hz
Secondary circuit: 100mA constant current at 9V Charger…
1020
Accesorio
FINAT 1 Peel Jig for 180 degree testing, QC-20
PDV13016-C
FINAT 1 Peel Jig - 180°
A polished steel plate used for affixing pressure-sensitive adhesive tape in accordance with FINAT 1 test method and other international standards.
Fitted with an adaptor having QC-20mm female hole for connection to the base of…
1021
Accesorio
Footswitch regulator option
Mec205-PR
Pressure regulator to adjust the air pressure between 1-10 bar.
Useful when a different pressure is required between upper and lower pneumatic grips.
To be ordered and fitted with either Mec205-1 or Mec205-2 Footswitches.
1022
Accesorio
Miniature Vice Grip, 100 N, QC-20 fitting
MecS341
Versatile, easy to use, and suitable for small components (eg bonded joints) where access is limited and tensile forces are below 100 N.
Clamping surfaces are machined with pyramid-shaped serrations to ensure optimum gripping force.
The flexible chain-…
1023
Accesorio
Dial Gauge Bracket Set
432-167
The dial gauge bracket set allows an analogue or digital comparator to be securely fitted to the MDD manual test stand. Digital comparators are suitable for measuring crosshead movement over short distances.
1024
Accesorio
Diamond coated jaws for Mec83 U-Form Pneumatic Vice Grip, 5 kN, 40 x 60 mm
Mec83-BD
Diamond Jaws (40mm x 60mm) - nickel-plated having clamping surface coated with synthetic diamonds.
Opening span = 0-10mm, 10-20mm or 20-30mm depending on which rod and piston are fitted to the Mec83 body.
For materials which need a “bite” to secure a…
1025
Accesorio
Compression Plate, Self-levelling, Hardened & Ground, 70 mm, 5-16 UNC
432-350
Self-levelling compression plates are ideal for general compression testing on a range of materials and finished products. Self-levelling allows parallelism to be set for those applications where it is critical to accurately measure the deformation of a…