Search results
2051
Caso de estudio
Prueba de extracción del accesorio del arco en la ropa
Requisito El cliente era un proveedor del importante minorista de ropa del Reino Unido, Marks & Spencer, quien estipula que todos los sujetadores y accesorios deben ser probados a prueba de fallas.
2052
[Page extract]
BS EN ISO 205
Adhesives. Wood adhesives for non-structural applications. Determination of tensile shear strength of lap joints.
2053
[Page extract]
ASTM E1820-18ae1
The ASTM E1820 test method covers procedures and guidelines for the determination of fracture toughness of metallic materials using the following parameters: K, J, and CTOD (δ). Toughness can be measured in the R-curve format or as a point value.
2054
[Page extract]
*corp 01M-01-309
To determine the elongation and recovery properties of elastic Tapes (Both Woven and Knitted), reflectives, elastic tie cords Decorative TPU Bonding and Bonding Tape.
2055
[Page extract]
FINAT FTM1
This test method is designed to quantify the permanence of adhesion or peelability of self-adhesive pressure sensitive) materials.
2056
Caso de estudio
Prueba de primavera estabilizada
Ejemplo de ingeniería personalizada Nuestro cliente necesitaba probar una serie de muelles pequeños y livianos bajo compresión. Para evitar el pandeo y el movimiento lateral de los resortes, se requería un eje de soporte o una varilla guía.
2057
[Page extract]
BS EN ISO 80369-1
BS EN ISO 80369 “Small-bore connectors for liquids and gases in healthcare applications. Connectors for intravascular or hypodermic applications”.
This standard replaces BS EN ISO 594-1: 1986, BS EN 20594-1:1994, and BS EN 1707:1997.
2058
[Page extract]
Speak to a testing expert
If you're looking to validate adhesive joint performance under realistic stress conditions, our applications specialists can help configure the
2059
[Page extract]
Step-by-step guide to conducting a CMT test
Prepare the specimen - Cut to size with clean edges, ensuring flutes remain undamaged, and condition as per the standard.
Calibrate the equipment - Check the load cell and platen alignment.
2060
[Page extract]
ASTM D7233-08
This test method covers a procedure for determining the number of fractures present when paintbrush filaments are bent.
2061
Caso de estudio
Validación de par de cierre
Requisito El cliente tenía varios probadores de par de cierre Tornado y deseaba realizar verificaciones de validación periódicas sin la necesidad de devolver las unidades a Mecmesin o a un laboratorio aprobado.
2062
[Page extract]
Challenges and best practices in peel testing
Common challenges
Material variability in thickness, surface treatment, or adhesive application.
Inconsistent specimen preparation.
Operator error from misalignment or incorrect grip tension.
Best pra
2063
[Page extract]
ISO 11339
ISO 11339:2010 specifies a T‑peel test for the determination of the peel strength of an adhesive by measuring the peeling force of a T‑shaped bonded assembly of two flexible adherends. This test procedure does not provide design information.
2064
[Page extract]
BS EN 2597
BS EN 2597 is test method covering tensile testing on carbon fibre reinforced plastics.
Before conducting BS EN 2597, it is important to read the entire specification. Standards can be obtained from appropriate standard authorities.
2065
[Page extract]
Advances in adhesive testing
Modern systems incorporate high-resolution digital sensors for precise force measurement, real-time data capture with analytical software, and automation to reduce operator influence.
2066
[Page extract]
TAPPI T 402
Standard conditioning and testing atmospheres for paper, board, pulp handsheets, and related products, Test Method TAPPI/ANSI T 402 sp-13
2067
[Page extract]
ISO 20344
This Standard specifies methods for testing footwear designed as personal protective equipment.
8 groups of tests from dimensions to mechanical properties and fluid resistance.
Supplemented by ISO 20345
2068
[Page extract]
TAPPI T 576
This test method decribes the procedure, using constant-rate-of-elongation, for determining three tensile breaking properties of towel and tissue: tensile strength, stretch, and tensi;e energy absorption.
2069
[Page extract]
BS EN ISO 7886-1
This document specifies requirements and test methods for verifying the design of empty sterile single use hypodermic syringes, with or without needle, made of plastic or other materials and intended for the aspiration and injection of fluids after fill
2070
[Page extract]
ASTM C297
This test method determines the flatwise tensile strength of the core, the core-to-facing bond, or the facing of an assembled sandwich panel.
2071
Caso de estudio
Prueba de resistencia de extracción de página
Requisito Mecmesin colaboró con un cliente para diseñar y desarrollar un sistema de medición de fuerza para determinar la fuerza adhesiva de encuadernación de libros en la retención de páginas individuales.
2072
[Page extract]
ASTM C961
This test method covers a laboratory procedure for determining the lap shear strength of sealants. It also provides information on the adhesive bond of the sealants to the tested substrates.
2073
[Page extract]
FINAT FTM2
This test method differs from FTM 1 in that it can allow the end user to compare the repositionability of different laminates.
2074
[Page extract]
Bancos de pruebas motorizados
Prueba de fuerza repetible ¿Busca un probador motorizado de tracción o compresión para mejorar la precisión y la repetibilidad de sus mediciones en comparación con los medidores de f
2075
Caso de estudio
Prueba de nitidez de la aguja hipodérmica
Ejemplo de ingeniería personalizada Las agujas hipodérmicas se prueban para determinar cómo su diseño influye en la facilidad de inserción en la piel, el dolor del paciente y el trauma de la piel.