Search results
1076
[Page extract]
ISO 6383-1
ISO 6383-1 specifies a method of determining the tear resistance of plastic film or sheet less than 1 mm thick, in the form of standard trouser-shaped test specimens, tested under defined conditions of pre-treatment, temperature, humidity, and speed of
1077
[Page extract]
ISO 1827
ISO 1827 specifies methods for the determination of the modulus in shear and the strength of bonds of rubber to metal or other rigid plates, using rubber bonded between four parallel plates.
1078
[Page extract]
ASTM D3032
These test methods detail the standard procedures for testing hookup wire insulations including all components of the insulation system used on single insulated conductors or an assembly of single insulated conductors such as a cable bundle and harness
1079
Event
Tensile Testing: Basics, Tips and Trends
Have you ever wondered if the seatbelt in your vehicle is strong enough to restrain you in a collision? How about the average person pulling the cork out of a wine bottle?
1080
Event
Tensile Testing: Basics, Tips, & Trends
Have you ever wondered if the seatbelt in your vehicle is strong enough to restrain you in a collision? How about the average person pulling the cork out of a wine bottle?
1081
[Page extract]
ISO 13935-1
ISO 13935-1:2014 specifies a procedure to determine the seam maximum force of sewn seams when the force is applied perpendicularly to the seam. ISO 13935-1:2014 specifies the method known as the strip test.
1083
[Page extract]
ISO 20795-1
ISO 20795-1:2013 classifies denture base polymers and copolymers and specifies their requirements. It also specifies the test methods to be used in determining compliance with these requirements.
1084
Event
Fundamentals of Food Texture Analysis
The primary goal for using instrumentation to measure texture is to capture an objective value to something that is typically evaluated very subjectively. Texture cannot be controlled unless it measured in a consistent and repeatable manner.
1085
Event
Fundamentals of Food Texture Testing and Analysis
Texture cannot be controlled unless it measured in a consistent and repeatable manner.
1086
[Page extract]
ASTM F3014-14
1.1 This test method describes the procedure for penetration testing sharp and blunt needles used for the placement of surgical sutures. It only describes the test procedures (Phase 1) and does not define a test medium at this time.
1087
Event
Fundamentals of Texture Testing Analysis
The primary goal for using instrumentation to measure texture is to capture an objective value to something that is typically evaluated very subjectively. Texture cannot be controlled unless it measured in a consistent and repeatable manner.
1088
[Page extract]
BS EN ISO 19011:2011
Provides the fundamental knowledge needed for auditing management systems and has been expanded to reflect modern thinking and the intricacies of auditing multiple management system standards (MSS).
1089
[Page extract]
ASTM F2132-01
This specification provides the performance requirements and associated test procedures for the puncture resistance of materials used in the construction of containers for discarded medical needles and other sharps.
1090
Caso de estudio
Luer lock fastening and release torque
Customised engineering example
Luer lock test standards frequently call for measuring torque whilst simultaneously applying a pre-defined axial force.
1091
Event
Tensile Testing: Basics, Tips, & Trends
Have you ever wondered if the seatbelt in your vehicle is strong enough to restrain you in a collision? How about the average person pulling the cork out of a wine bottle?
1092
Event
Tensile Testing: Basics, Tips and Trends
Have you ever wondered if the seatbelt in your vehicle is strong enough to restrain you in a collision? How about the average person pulling the cork out of a wine bottle?
1093
Event
Understanding Adhesion Strength: 180 Degree Peel Test
Across many households and industries, consumers have developed a strong preference for and confidence in ‘Duct Tape’ for all types of uses and applications. This is mainly due to the adhesion strength.
1094
Event
Understanding Adhesion Strength: 180 Degree Peel Test
Across many households and industries, consumers have developed a strong preference for and confidence in ‘Duct Tape’ for all types of uses and applications. This is mainly due to the adhesion strength.
1095
Caso de estudio
Pruebas con jeringa según ISO 11040-4 Anexo F: Pruebas de penetración y arrastre de la aguja
Explore esta completa guía sobre ensayos con jeringuillas según la norma ISO 11040-4, anexo F. Conozca el proceso paso a paso de las pruebas de penetración y arrastre de la aguja, el equipo necesario y las mejores prácticas para obtener resultados…
1096
Accesorio
Blank (smooth) jaws for Mec240k Medium Vice Grip, 2.5 kN, 30 x 50 mm
Mec240k-B50
Blank Jaws (30mm x 50mm) - smooth steel jaw. Allows user to machine or affix own surface (eg. abrasive 'emery' paper).
Opening span = see datasheet for various spans according to the grip body selected.
Supplied as 0.5 set = 2 jaws (left…
1097
Accesorio
Lightweight hanger and 5 N slotted mass for verifying FPT 10 N
432-655
A lightweight hanger and an M1 slotted mass of 5N.
For use with the FPT-H1 loadcell calibration checking kit (432-635) to verify the accuracy of HILC 10 N loadcells.
1098
Accesorio
Lightweight hanger and 50 N slotted mass for verifying FPT 100 N
432-656
A lightweight hanger and an M1 slotted mass of 50N.
For use with the FPT-H1 loadcell calibration checking kit (432-635) to verify the accuracy of HILC 100 N loadcells.
1099
Accesorio
Wave jaws for Mec240k Medium Vice Grip, 2.5 kN, 30 x 30 mm
Mec240k-BW
Wave Jaws (30mm x 30mm) - nickel-plated having a hardened steel surface of 5mm tall waves.
For flexible but slippy materials which need more surface contact to secure a good grip (e.g. textiles, fabrics and tissues).
Supplied as 0.5 set = 2 jaws (left…
1100
Accesorio
Blank (smooth) jaws for Mec240k Medium Vice Grip, 2.5 kN, 30 x 30 mm
Mec240k-B
Blank Jaws (30mm x 30mm) - smooth steel jaw. Allows user to machine or affix own surface (eg. abrasive 'emery' paper).
Opening span = see datasheet for various spans according to the grip body selected.
Supplied as 0.5 set = 2 jaws (left…