Search results
1501
[Page extract]
TAPPI T 840
This method describes a procedure for evaluating the adhesive used in glued lap joints of corrugated containers.
1502
[Page extract]
BS EN 12453
BS EN 12453:2001 specifies the performance requirements with regard to the safety in use for any type of power operated doors, gates and barriers intended for installation in areas in the reach of persons, and for which the main intended uses are giving
1503
[Page extract]
ASTM D4649-03
This guide covers recommended guidelines and test methods for the selection, specification, and use of stretch wrap films for unitizing, reinforcing, and palletizing for indoor environments.
1504
[Page extract]
ISO 6425
This document specifies requirements and test methods for divers' watches and for saturation divers' watches for use in deep diving (see Annex A which deals with watches for saturation diving).
1505
[Page extract]
ASTM D4255 / D4255M-15a
ASTM D4255 is a test method for testing the in-plane shear properties of high-modulus fiber-reinforced composite materials. The method is divided into two procedures. Procedure A tests laminates clamped between two pairs of loading rails.
1506
[Page extract]
ASTM D695-15
ASTM D695 is a test method used to determine the mechanical properties of unreinforced and reinforced rigid plastics, including high-modulus composites, when loaded in compression at relatively low uniform rates of straining or loading.
1507
Caso de estudio
Prueba de par de cierres CRC con una fuerza descendente controlada neumáticamente
Requisito Los cierres a prueba de niños (CRC) vienen en muchos diseños y son vitales para la prevención de daños por productos químicos o farmacéuticos tóxicos. El tipo de cierre depende a menudo del contenido del envase y del envase.
1508
Event
Cork Pull & Cork Compression Testing OnDemand Webinar
FORCE TESTING in Wine & Spirit Applications
1509
Caso de estudio
Prueba de válvulas de control de fluidos y sellos
Requisito Un sistema de elevación de gas típico para la producción de petróleo y gas requiere un conjunto de válvulas para operar a lo largo del tubo de producción en el pozo de perforación.
1510
[Page extract]
Government
The general government sector covers institutions and public bodies where regulations and standards must be strictly adhered to.
1511
Caso de estudio
Retoque el empaque de 90 grados de prueba de resistencia al pelado y la tapa
Requisito La industria del envasado de alimentos lleva mucho tiempo preocupada por los agujeros, las grietas flexibles y las fugas en los materiales flexibles y los sellos de los envases con tapa flexible de retorta.
1512
[Page extract]
Understanding test types
Material testing uses a variety of methods to assess different mechanical properties. Selecting the right test depends on the intended application and relevant standards.
Examples include:
1513
[Page extract]
What is wing tear testing (Winkelmann/Graves method)?
Wing tear testing is a tensile-based method for flexible materials, in which a wing-shaped specimen is subjected to a controlled force until it tears.
1514
[Page extract]
Differences and similarities to other corrugated tests
While TAPPI T 824 focuses on the intrinsic crush strength of pre-fluted medium, other common corrugated tests measure different performance factors:
1515
[Page extract]
Why Mecmesin?
With over 40 years of experience, Mecmesin delivers torque testing systems that are precise, easy to use, and fully supported.
1516
[Page extract]
Introduction to double rip tongue tear testing
Double rip tongue tear testing is a recognised method for assessing the tear resistance of flexible materials including co
1517
[Page extract]
Common challenges and solutions
Misalignment can cause uneven peeling forces.
1518
[Page extract]
Methods of testing tensile strength
The most common method is the uniaxial tensile test.
1519
[Page extract]
Introduction to equibiaxial flexure compression testing
Equibiaxial flexure compression testing is a materials testing method used to evaluate a specimen’s resistance to bending under multi-directional loading.
1520
[Page extract]
Why is the trapezoidal tear test important?
Tear resistance is a critical measure of a material’s durability, particularly in applications where the material may be subject to punctures, cuts, or repeated stress.
1521
[Page extract]
What is lap shear testing under compression?
Lap shear testing under compressive load is a mechanical test used to determine the strength of adhesive joints subjected to shear forces while under compressive stress.
1522
[Page extract]
Applications and benefits
Industrial applications
Tension and compression testing is used across multiple industries to validate design performance, assure quality, and meet regulatory requirements:
1523
[Page extract]
Why is top-load testing important?
Top-load testing plays a critical role in packaging design, quality assurance and compliance. It helps to:
1524
[Page extract]
Speak to an Expert
Corrugated medium testing, and particularly the flat crush test under TAPPI T 809, is essential for ensuring packaging strength, reliability, and compliance.
1525
[Page extract]
Puncture resistance testing methods
Puncture resistance measures the ability of a material to withstand an actual perforation event, simulating damage from sharp or pointed objects.
Applications include: