Search results
2276
[Page extract]
ASTM D5528-13
ASTM D5528 is a test method, which determines the opening Mode I interlaminar fracture toughness of continuous fiber-reinforced composite materials. It uses a a double cantilever beam (DCB) specimen. Susceptibility to delamination is one of the major
2277
[Page extract]
ASTM D3480
These test methods cover the measurement of the downward force required to open or activate child-resistant snap-engagement packages.
2278
[Page extract]
ASTM D3474
This standard covers the calibration and use of torque meters of the type normally used in packaging applications.
2279
[Page extract]
ANSI/EIA 364-38B
This standard establishes a test method to determine the axial tensile load that can be applied to a mated pair of connectors and the holding effect of a connector cable clamp without causing any detrimental effects upon the cable or connector when subj
2280
[Page extract]
ASTM D5868-01
Due to the increased use of adhesively-bonded FRP as a result of the inherent advantages afforded by bonded rather than mechanically-fastened joints (particularly the alleviation of stress risers and stress cracking), there is a need for tests by which
2281
[Page extract]
BS 2782-3: 360C
BS 2782-3: Method 360C specifies a test method for testing the tear resistance of plastics film and sheeting by the initiation method
2282
[Page extract]
BS EN 2591-408
Gives a procedure for measuring the mating and unmating forces for elements of connection.
2283
[Page extract]
ASTM D1600
ASTM D1600 is a source of reference for definitions of abbreviated technical terms used in the plastics industry
Standards can be obtained from appropriate standard authorities.
2284
[Page extract]
BS EN ISO 13262
BS EN ISO 13262 is test method to determine the tensile strength of seams on thermoplastics spirally-formed structured-wall pipes.
2285
[Page extract]
ANSI/EIA 364
Mating and Unmating Procedure for Force Testing of Electrical Connectors and Sockets
2286
[Page extract]
ISO 12625-5
ISO 12625-5:2005 specifies a test method for the determination of the wet tensile strength of tissue paper and tissue products after soaking with water, using a tensile-strength-testing apparatus operating with a constant rate of elongation.
2287
[Page extract]
Drucksonden
Drucksonden sind in erster Linie für Penetration und Durchstoßfestigkeitsprüfung ausgelegt.
2288
[Page extract]
Belt/strap grips
Belt and strap grips - typically of a split-roller type in order to provide a rounded, smooth-surface around which a belt or strap can be looped several times.
2289
[Page extract]
BS EN 29073-3
Non-woven cloth, Cloth, Textile products, Tensile testing, Testing conditions, Test specimens, Dimensions, Specimen preparation, Textile testing, Fabric testing
2290
[Page extract]
CETIE Guide 9
This guide applies to the screw capping of pressurised wines & other beverages for narrow necks finishes with a redrawn metallic tamper-evident closure on a "BVS type" glass finish adapted for pressure caps. Includes sections on checking load setting on
2291
[Page extract]
BS EN ISO 10591
This International Standard specifies a method for the determination of the influence of water on the adhesion cohesion properties of sealants with predominantly plastic behaviour which are used in joints in building construction.
2292
[Page extract]
ISO 6237
Specifies a method for determining the shear strength of wood-to-wood adhesive bonds, with a standard specimen loaded in tension and under specified conditions of preparation, conditioning and testing.
2293
[Page extract]
ISO 2493-1
Specifies procedures, based on the two-point loading principle, for determining the bending resistance of paper and board.
2294
[Page extract]
ASTM D5379/D5379M-05
This test method covers the shear properties of composite materials reinforced by high-modulus fibers. The composite materials are limited to continuous-fiber or discontinuous-fiber-reinforced composites in specific forms.
2295
[Page extract]
ASTM C1469
This test method covers the determination of shear strength of joints in advanced ceramics at ambient temperature.
2296
[Page extract]
SAE J 1907
This recommended practice defines a procedure for the construction and testing of a 180 deg peel specimen for the purpose of determining the bondability of glass to elastomeric material in automotive modular glass.
2297
[Page extract]
ASTM D1894
This test method is used to measure the friction of plastic film and sheeting. It determines the kinetic (moving) and static (starting) resistance of one surface being dragged across another.
2298
[Page extract]
TAPPI T 838
This method describes a procedure for determining the edgewise compressive strength, parallel to the flutes, of a short column of singe, double, or triple-wall corrugated fiberboard, in a neckdown, non reinforced, loading edge configuration.
2299
[Page extract]
ASTM E2658-15
These practices cover procedures and requirements for the calibration and verification of testing machine speed by means of standards calibration devices
2300
[Page extract]
ASTM D1876
This test method measures the peel separation strength of two flexible materials that have been bonded together.