Search results
1276
[Page extract]
FAQs
Find answers to common questions about syringe testing and ISO 11040-4:
1277
[Page extract]
ASTM D4501-01
This test method describes a procedure and fixture used to determine shear strengths of adhesives used to bond materials with moduli higher than the modulus of the adhesive.
1278
[Page extract]
ISO 8364
ISO 8364:2007 specifies requirements and test methods for the binding mounting area and free space area, ski bindings and retention devices of alpine skis, in order to optimize the compatibility of the functional unit "ski binding - retention device - b
1279
[Page extract]
Methods and applications
Common test methods
Most single lap shear tests are carried out under tensile loading, but the method can vary depending on material type, bond configuration and industry require
1280
[Page extract]
When High Ultimate Tensile Strength is a Disadvantage
While high UTS materials are strong, they can also be brittle and less ductile.
1281
[Page extract]
Manual test stands
Manual test stands allow simple force testing when budgets are limited.
Lever-operated models enable rapid testing of tension and compression up to 500 N.
1282
[Page extract]
ASTM D5467 / D5467M-97
ASTM D5467 is a test method that determines the in-plane compressive properties of polymer matrix composite materials reinforced by high-modulus fibers in a sandwich beam configuration.
1283
[Page extract]
ASTM D6049-03
This test method is capable of measuring and characterizing the rheological behavior (viscosity and elasticity) of unvulcanized raw rubbers and rubber compounds, relating to the macro structure of rubber polymers (average molecular weight, molecular wei
1284
[Page extract]
Understanding cone penetration testing
Cone penetration testing is a precision method used to determine a material's resistance to penetration by a standardised cone-shaped probe under specific force conditions.
1285
Case study
Synthetische Sportoberflächenbindung
Beispiel für kundenspezifisches Engineering Die Prüfnorm ISO 4919 gilt für die Büschelabzugskraft von Teppichen.
1286
[Page extract]
FINAT FTM2
This test method differs from FTM 1 in that it can allow the end user to compare the repositionability of different laminates.
1287
[Page extract]
Introduction to friction in material science
Friction is a critical factor in how materials behave under movement. It is the resistive force that occurs when two surfaces are in contact and attempt to slide against each other.
1288
[Page extract]
ISO 36
ISO 36 determines the strength required to separate two plies of fabric bonded together with rubber, or a rubber and a fabric ply bonded together. This test is referred to as a “T-peel” test, because as the two adherends are pulled apart, they form the
1289
[Page extract]
ASTM D790-17
ASTM D790 is used to determine the flexural properties of unreinforced and reinforced plastics, including high modulus composites and electrical insulating materials utilizing a three-point loading system to apply a load to a simply supported beam (spec
1290
[Page extract]
Mecmesin equipment for 180 degree peel testing
Mecmesin provides a complete range of test solutions designed for accurate and repeatable peel strength measurement.
1291
[Page extract]
Standards for box crush testing
ASTM D642-00
This standard specifies methods for determining the compressive resistance of shipping containers, both filled and empty.
1292
[Page extract]
Introduction to tear testing
Tear testing is a quality control procedure used to measure the resistance of a material to tearing under controlled conditions.
1293
[Page extract]
Standards and guidelines for torque testing
Overview of ASTM and CETIE standards
Standardised testing ensures consistency and compliance. Commonly followed guidelines include:
1294
[Page extract]
Application of standards in puncture testing
Standardised methods ensure test consistency and reliability across laboratories and production sites.
1295
Software
VectorPro Lite software (force instruments)
VectorPro® Lite software
Available as an optional extra to Mecmesin's Digital Force Gauges (VFG, AFG, BFG and CFG+ and VFTI/AFTI Digital Force Indicators, VectorPro Lite is an advanced data acquisition and plotting software package.
Simply select the…
1296
[Page extract]
Why Mecmesin for bulk analysis
Expert engineering and equipment
Mecmesin systems are designed for precision and reliability in bulk testing applications.
1297
[Page extract]
ISO 20502
SO 20502:2005 describes a method of testing ceramic coatings by scratching with a diamond stylus.
1298
[Page extract]
ASTM D349
These test methods cover the procedures for testing rigid round rods used in electrical insulation.
1299
[Page extract]
ASTM D4482-11
ASTM D4482 is a test method used to determine the fatigue life of rubber compounds undergoing a tensile-strain cycle. During part of the cycle, the strain is relaxed to a zero value.
1300
[Page extract]
ASTM D3577
1. Scope ... 1.1 This specification describes certain requirements for packaged sterile rubber surgical gloves used in conducting surgical procedures.