Search results
2401
[Page extract]
IEC 60512-13-1
Details a standard test method to measure the force to fully engage or separate mating connectors, including the effect of any locking, latching, sealing, engaging, separating or similar device, that assists or resists such operation.
2402
[Page extract]
ISO 11607-1
Specifies the requirements and test methods for materials, preformed sterile barrier systems, sterile barrier systems and packaging systems that are intended to maintain sterility of terminally sterilized medical devices until the point of use.
2403
Case study
90-Grad-Schältestfilterpapier
Beispiel für kundenspezifisches Engineering Schwimmende Rollenschälvorrichtungen werden regelmäßig zum Testen von Laminaten verwendet, bei denen die Trägerfolie starr und die Deckfolie flexibel ist (z. B. Sicherheitskarten).
2404
[Page extract]
IPC TM-650
A suite of test methods for printed circuit boards. Visual, dimensional, chemical, mechanical, electrical, environmental. To determine the release strength of the carrier of thin copper foil in pounds per inch of width at ambient temperature
2405
Case study
Inline-Atemfilter-Zugtest
Beispiel für kundenspezifisches Engineering Ein Hersteller von Filtrationsprodukten musste die Absaugkraft eines Atemfilter prüfen, wenn dieser aus einem medizinischen Inline-Gerät gezogen wurde.
2406
[Page extract]
BS 6319-6
BS 6319-6 is a test method for determining the modulus of elasticity in compression of resin and polymer/cement compositions for use in construction.
2407
[Page extract]
BS EN 12814-6
BS EN 12814-6 is a low temperature tensile test method for testing welded joints of thermoplastics semi-finished products.
2408
[Page extract]
TAPPI T 838
This method describes a procedure for determining the edgewise compressive strength, parallel to the flutes, of a short column of singe, double, or triple-wall corrugated fiberboard, in a neckdown, non reinforced, loading edge configuration.
2409
[Page extract]
ASTM D1871
This test method is used to test the strength of adhesion of single-filament wire to vulcanized rubber compounds. It applies to wire made from brass, bronze or zinc coated steel wire.
2410
Case study
Nadel-zu-Ferrule-Ausziehtest
Anforderung Der Kunde, Oxford Instruments, wollte einen zerstörerischen Auszugstest durchführen, um die maximale Zugkraft zum Auseinanderziehen der beiden Komponenten zu ermitteln.
2411
[Page extract]
TAPPI T 810
This method describes a procedure for measuring the bursting strength of single wall and double wall corrugated board within the range of 690 kPa (100psi) to 4825 kPa (700 psi) employing an instrument which uses a disk shaped, molded diaphragm.
2412
[Page extract]
ASTM C1341
This test method covers the determination of flexural properties of continuous fiber-reinforced ceramic composites in the form of rectangular bars formed directly or cut from sheets, plates, or molded shapes.
2413
[Page extract]
BS EN 1270
Basketball equipment, Ball-games equipment, Sports equipment, Classification systems, Dimensions, Safety measures, Performance, Properties, Performance testing, Mechanical testing, Sports nets.
2414
Case study
Festliche Festigkeitsüberprüfung des Mauerwerks der Beleuchtung
Anforderung Eine Reihe von Kommunen im Vereinigten Königreich haben einen neuen Verhaltenskodex für die Installation, den Betrieb und die Entfernung von saisonalen Dekorationen verabschiedet.
2415
[Page extract]
ASTM D4964-96
5.1 This test method for testing loop tension and elongation of elastic fabrics is considered satisfactory for acceptance testing of commercial shipments of elastic fabrics because the test method is used in the trade for acceptance testing.
2416
[Page extract]
ASTM D5170-98
This test method covers the measurement of the peel strength of hook and loop touch fasteners using a recording constant-rate-of-extension tensile testing machine (CRE).
2417
Case study
Quetsch- und Bruchfestigkeit von pharmazeutischen Tabletten
Anforderung
Viele Produkte werden in Tablettenform mit einer Haltbarkeit geliefert, die sowohl für die Verpackung als auch für den Gebrauch ausgelegt ist.
2418
Specials
Thermal cabinet environment chamber
Environmental chamber capability
Mecmesin's OmniTest twin column range can accommodate an environmental chamber to test materials in controlled ambient conditions.
2420
Case study
Identitätskarten abziehen
Anforderung Der Kunde stellt Ausweise mit laminiertem Umschlag her.
2421
[Page extract]
ASTM C1161
This test method covers the determination of flexural strength of advanced ceramic materials at ambient temperature. Four-point and three-point loadings with prescribed spans are the standard.
2422
Case study
Drehmomentprüfung von kindersicheren Verschlüssen
Anforderung Reckitt-Benckiser ist Hersteller der charakteristischen "Harpic" -Reinigungsflüssigkeitsflaschen aus HDPE (High Density Polyethylen).
2423
[Page extract]
ISO 252
ISO 252 specifies two test methods, A and B, for determining the adhesion strength between constitutive elements of a conveyor belt, i.e. between plies and between covers and carcass.
2424
[Page extract]
BS 7548
Describes requirements and test methods for sterile syringes
with or without needles for single use solely for the injection
of insulin in humans. Covers syringes for use with 40 units of