Search results
501
[Page extract]
ASTM F1566-09
These test methods cover recognized methods for testing mattress innersprings, boxsprings, and finished mattresses or mattress sets, or both, to ensure uniformity of results.
502
[Page extract]
ASTM D953-18
ASTM D953 is a test method that covers the determination of the pin-bearing strength of rigid plastics in either sheet form, molded form, or in reinforced thermoset form.
503
Case study
Testen von Schulterprothesen
Anforderung Herr Keith Borowsky, ein angesehener Orthopäde an der University of Brighton Medical School, entwickelt eine neue orthopädische Prothese für die Schulterrekonstruktion.
504
[Page extract]
EN TS 15945
The purpose of DD CEN/TS 15945 is to specify test methods to evaluate the ease of opening of consumer packages, in order to improve easy access to the contents. For packages regulated for safety or similar reasons, e.g.
505
Case study
Beleuchtungsschweißtest
Anforderung Für das Qualitätskontrolllabor wurde vom Kunden eine einfache, kostengünstige Vorrichtung spezifiziert. Dies sollte eine Beleuchtungsbaugruppe in einem Test halten, bei dem die geschweißten Kontakte abgezogen wurden.
506
[Page extract]
MIL 22520-G
This specification covers the general requirements for crimping tools, accessories and inspection gages used for connecting removable contacts (such as; signal, power, coaxial, shielded, thermocouple, and filter pin contacts) coaxial connectors, shielde
507
Event
Medical Devices – Syringe & Needle Testing Fundamentals
Vial sealing is a critical step in the process of ‘fill and finish’ operations for vaccines and medications, as it defines the seal quality of the final product, ensuring sterility and preventing leakage.
508
Event
Fundamentals of Torque Testing
If you have ever struggled to open your favorite bottle of water or jam or required help loosening the lug nuts on your car’s wheels, it is likely due to a case of over-torque.
509
Case study
Connection test on fuel injection components
Requirement
A number of destructive and non-destructive tests were required on a plastic assembly used in a fuel injection assembly. The tests included:
510
Case study
90-Grad-Prüfung der Schäl- und Deckelfestigkeit von Retortenverpackungen
Anforderung Die Lebensmittelverpackungsindustrie hat lange Bedenken hinsichtlich Nadelstichen, Biegerissen und Undichtigkeiten in den flexiblen Materialien und Siegeln von Retortenverpackungen mit flexiblen Deckeln.
511
Event
Tensile Testing for Wiring Harness Connections Webinar
The only way of really knowing the strength of a crimped terminal is to pull it.
512
Case study
Entfernen des Spritzen-Luer-Lock-Aufsatzes
Beispiel für kundenspezifisches Engineering Unser Kunde ist ein biomedizinisches Unternehmen, das medizinische HA-Lösungen herstellt, die in Glasspritzen mit klemmbaren Luer-Locks aus Polycarbonat geliefert werden.
513
Case study
Pumpspender Flaschenbetrieb
Beispiel für kundenspezifisches Engineering Als Methode zur Abgabe von Flüssigkeiten und Sprays werden Treibgase wie Druckgas aus vielen Gründen vermieden. An ihrer Stelle werden häufig Spender mit manuellen gefederten Pumpen eingesetzt.
514
[Page extract]
Tools and equipment for shear testing
Accurate shear testing in tension requires high-quality, precise equipment:
515
Bundle
Top-load PET bottle CSD non-vented
OmniTest 2.5
BD
Top-load testing (also known as 'column-crush' and 'axial force resistance') is performed mainly on blow moulded, thermoformed or injection moulded plastic containers such as PET (Polyethylene terephthalate) bottles.
516
Case study
Electrical connector insertion and withdrawal forces
Customised engineering example
Push-fit electrical connectors with hole or dimple detents (also known as 'spade terminals') must offer a firm but practical fit.
517
Case study
Geosynthetische Biegefestigkeit von zementhaltigen Verbundmatten
Anforderung Concrete Canvas Ltd. setzt bei seinem Concrete Canvas® GCCM-Produkt, das im Wesentlichen aus Beton auf einer Rolle besteht, auf bahnbrechende Materialtechnologie.
518
[Page extract]
Test setup and equipment
Performing lap shear testing under compression requires careful alignment and use of appropriate fixtures to prevent torsion or uneven load distribution.
519
[Page extract]
BS EN ISO 9001
ISO 9001 has been revised to reflect the many changes in the way we now do business – new technology, greater access to information, higher customer expectations, globalization and increasing importance of service industries.
520
Event
Fundamentals of Torque Testing
If you have ever struggled to open your favorite bottle of water or jam or required help loosening the lug nuts on your car’s wheels, it is likely due to a case of over-torque.
521
Case study
Zug- und Druckprüfungen für die Ausbildung in Festkörpermechanik
Anforderung
Das Department of Bioengineering am Imperial College London war eine Pionierorganisation bei der Formulierung dieser Disziplin und ist heute die führende Einrichtung ihrer Art in Großbritannien.
522
Case study
Crimped cable connector pull-off force
Requirement
Amphenol is a global interconnect specialist; a world leader in the design, manufacture and supply of high-performance interconnect systems.
523
Case study
Zugfestigkeitstest der Seite
Anforderung Mecmesin arbeitete mit einem Kunden zusammen, um ein Kraftmesssystem zu entwickeln, mit dem die Klebkraft der Buchbindung bei der Aufbewahrung einzelner Seiten bestimmt werden kann.
524
Case study
Coefficient of friction test on plastic film
Requirement
A print factory needed to test the packaging material they were using in order to improve their processes and establish optimum machinery settings.
525
[Page extract]
Tools and techniques for measuring torque
Manual vs motorised torque testers
Manual torque testers are suited to spot checks or lower-volume testing.