Search results
3051
[Page extract]
IPC TM-650
A suite of test methods for printed circuit boards. Visual, dimensional, chemical, mechanical, electrical, environmental. To determine the release strength of the carrier of thin copper foil in pounds per inch of width at ambient temperature
3052
[Page extract]
ISO 2555
Specification of a method for determining an apparent viscosity of resins in a liquid state, using one of the types of rotational viskosimeter described in this standard.
3053
[Page extract]
BS EN ISO 3376
This International Standard specifies a method for determining the tensile strength , elongation at a specified load and elongation at break. It is applicable to all types of leather
3054
[Page extract]
ASTM D3471
This test method covers the determination of the top-load required to engage lugs on Type IA child-resistant closures.
3055
[Page extract]
AEC Q200-005
This specification establishes the procedure and criteria to determine the ability of surface
mounted device terminations and seals to withstand bending, flexing and pulling forces which
3056
[Page extract]
ASTM D1871
This test method is used to test the strength of adhesion of single-filament wire to vulcanized rubber compounds. It applies to wire made from brass, bronze or zinc coated steel wire.
3057
[Page extract]
TAPPI T 810
This method describes a procedure for measuring the bursting strength of single wall and double wall corrugated board within the range of 690 kPa (100psi) to 4825 kPa (700 psi) employing an instrument which uses a disk shaped, molded diaphragm.
3058
[Page extract]
ASTM D1566
ASTM D1566 is a source of reference for definitions of technical terms used in the rubber industry
Standards can be obtained from appropriate standard authorities.
3059
[Page extract]
BS EN 60352-2
Solderless connectors, Electric connectors, Crimped connectors, Electrical components, Electronic equipment and components, Electrical connections, Communication equipment, Crimping tools, Dimensions, Mechanical crimping, Dimensional measurement, Electr
3060
[Page extract]
SAE AS7928
This specification covers insulated and uninsulated crimp-style copper terminal lugs and conductor splices for stranded conductors. An Amendment corresponding to this standard is available at AS7928_A1
3061
Event
Materials Testing: Theory and Practice Pt. 1
Materials testing is often the last step in the manufacturing process. Yet, quality is the result of both the process and the material. If the material that goes into the product is inadequate or defective, then the product may be deficient or faulty.
3062
[Page extract]
BS EN 564
Mountaineering equipment, Mountaineering ropes, Cords, Outdoor sports equipment, Sports equipment, Diameter, Tensile strength, Safety measures, Equipment safety, Marking, Instructions for use, Diameter measurement, Weight measurement
3063
[Page extract]
ASTM D3822
This test method covers the measurement of tensile properties of natural and man-made single textile fibers of sufficient length to permit mounting test specimens in a tensile testing machine.
3064
[Page extract]
NF G30-102
La présente partie a pour objet de décrire une méthode de mesure directe de la pression de contention des garnitures élastiques telles que les bords-côtes de chaussettes, ceinturesde slips et de culottes, gaines et bas dits de confort, et plus généralem
3065
[Page extract]
ASTM D3518 / D3518M
ASTM D3518 is a test method, which measure the shear stress and shear strain properties of polymer matrix composite materials composed of +45 plies and -45° plies.
3066
[Page extract]
ASTM D4482-11
ASTM D4482 is a test method used to determine the fatigue life of rubber compounds undergoing a tensile-strain cycle. During part of the cycle, the strain is relaxed to a zero value.
3067
[Page extract]
ASTM D5672-09
This test method covers a screening type quality control test used to determine if flexible polyurethane foam cushions are within the specified grade range for firmness.
3068
[Page extract]
ASTM B913
This test method establishes the requirements for a standardized method of evaluating the quality of crimped-type electrical connections to solid or stranded conductors.
3069
[Page extract]
ASTM F607-03
The ASTM F607 test method provides a means of determining the degree to which gasket materials under compressive load adhere to metal surfaces. The test conditions described are indicative of those frequently encountered in gasket applications.
3070
[Page extract]
Druck
Druckproben werden durchgeführt, um die Leistung eines Materials oder einer Komponente unter allmählich zunehmender Druckbelastung zu bewerten.
3071
[Page extract]
ASTM D7834-13
During the application of coatings, paint brushes can exhibit shedding of filling material onto the coated surface. A measure of this shedding filling material will determine the paint brush’s ability to resist shedding during application.
3072
[Page extract]
*corp QPF-MC-1209 B
*Strictly confidential*
L'Oreal to methods for shear and penetration testing of lipsticks, deodorants etc.
3073
[Page extract]
BS EN 12467
Sheet materials, Asbestos cement, Cements, Fibres, Reinforced materials, Sheet roof coverings, Cladding (buildings), Curtain walling, Grades (quality), Density, Strength of materials, Approval testing, Type testing, Quality control, Acceptance inspectio
3074
[Page extract]
ASTM D7264 / D7264M-15
ASTM D7264 is a test method used to determine the flexural stiffness and strength properties of polymer matrix composites. The test method summarises two procedures:
3075
[Page extract]
ASTM F1473-18
ASTM F1473 is a test method determines the resistance of polyethylene materials to slow crack growth. It is also known as PENT (Pennsylvania Notch Test) test.