Search results
1901
Case study
Luer-Lock-Befestigung und Lösemoment
Beispiel für kundenspezifisches Engineering Luer-Lock-Teststandards fordern häufig die Messung des Drehmoments bei gleichzeitiger Anwendung einer vordefinierten Axialkraft.
1902
[Page extract]
ASTM F2824-10
1.1 This test method describes a method for the measurement of mechanical seal strength while separating the entire lid (cover/membrane) from a rigid or semi-rigid round container. 1.2 This test method differs from Test Method F88.
1903
[Page extract]
ASTM F37-00
1.1 These test methods provide a means of evaluating the sealing properties of sheet and solid form-in-place gasket materials at room temperature.
1904
Case study
Tensile test on rubber gaskets
Requirement
British Gaskets are a major manufacturer of gaskets, sealing products and mouldings. These are made from a variety of materials to suit a range of applications.
1905
[Page extract]
BS ISO 5893
ISO 5893 specifies requirements for tensile-testing systems operating at constant rate of traverse and suitable for testing rubbers, plastics and adhesives, although any one system may only be applicable to a narrower range of materials.
1906
Case study
Karton diagonale kante druckfestigkeit
Beispiel für kundenspezifisches Engineering Neben der axialen Belastungstestung an den Flachseiten von Kartonagen kann die Druckfestigkeit über die gegenüberliegenden Kanten ein wichtiges Maß sein.
1907
Case study
Torsionsfederprüfung
Beispiel für kundenspezifisches Engineering Im Gegensatz zu den meisten Druck- und Zugfedern werden Torsionsfedern in verschiedenen Formen mit unterschiedlichen Beinpositionen hergestellt.
1908
Event
Needle Sharpness & Puncture Resistance Testing
Hypodermic needles are tested to determine how their design influences the ease of insertion into the skin, patient pain and skin trauma.
1909
[Page extract]
BS EN 14704-1
Methods for testing using stripsof fabric in straight strip form or loops, which can be used to measure elasticity and related properties of fabrics, excluding narrow fabrics.
1910
Page
Kalibrierung
Mecmesin ist bestrebt, seinen Kunden weltweit den bestmöglichen Kundendienst zu bieten. Um Ihre Kraft- und Drehmomentprüfgeräte in einem erstklassigen Zustand zu halten, können Sie sich immer auf unser Team von Vertriebshändlern und regionalen…
1911
Case study
Torsion spring testing
Customised engineering example
Unlike most compression and tension springs, torsion springs are produced in a variety of forms with differing leg positions.
1912
Case study
Connection test on fuel injection components
Requirement
A number of destructive and non-destructive tests were required on a plastic assembly used in a fuel injection assembly. The tests included:
1913
[Page extract]
ISO 9895
Specifies a method for determining the compressive strength in the machine and cross-directions of paper and board using a short-span compressive tester. It is intended for papers and boards used for the manufacture of containers and boxes.
1914
[Page extract]
ASTM D3481
This test method covers the measurement of the force required to separate (or “shell”) the snap-fitted outer cap from the inner cap of Type IA, IB, or IC child-resistant closures.
1915
[Page extract]
ISO 6383-1
ISO 6383-1 specifies a method of determining the tear resistance of plastic film or sheet less than 1 mm thick, in the form of standard trouser-shaped test specimens, tested under defined conditions of pre-treatment, temperature, humidity, and speed of
1916
[Page extract]
ASTM D790-17
ASTM D790 is used to determine the flexural properties of unreinforced and reinforced plastics, including high modulus composites and electrical insulating materials utilizing a three-point loading system to apply a load to a simply supported beam (spec
1917
[Page extract]
ASTM D1683
This test method measures the sewn seam strength in woven fabrics by applying a force perpendicular to the sewn seams.
1918
[Page extract]
ISO 10768
This International Standard specifies a test method for the determination of the resistance of elastic materials for footwear, to repeated extension produced during normal walking. The test can be carried out before and after accelerated ageing.
1919
Case study
Karden- und Papierfaltenlinienprüfung
Beispiel für kundenspezifisches Engineering Eine Verpackungsproduktionsfirma musste die Knickkraft der mit Tinte beschichteten Karte testen, die in ihren vollständig geschlossenen Kartons verwendet wurde.
1920
[Page extract]
ASTM D2344 / D2344M
ASTM D2344 is a test method, which determines the short-beam strength of high-modulus fiber-reinforced composite materials. It is applicable to all types of parallel fiber reinforced plastics and composites.
1921
Case study
Page pull strength test
Requirement
Mecmesin collaborated with a customer to design and develop a force measurement system to determine book binding adhesive strength in retaining individual pages.
1922
Page
Fehlender Link
Die von Ihnen angeforderte Seite wurde auf dieser Website nicht gefunden. Es hätte sich bewegen können oder etwas ist schief gelaufen.
1925
[Page extract]
ASTM D624-00
This test method describes procedures for measuring a property of conventional vulcanized rubber and thermoplastic elastomers called tear strength.