Search results
2501
[Page extract]
ASTM D5766 / D5766-M
ASTM D5766 is a test method to determine the open-hole tensile strength of multidirectional polymer matrix composite laminates reinforced by high-modulus fibres.
2502
[Page extract]
NF S86-604
This document defines the test methods for characterizing metallic watch straps and the corresponding requirements.
2503
[Page extract]
ASTM C203
ASTM C203 is a test method that covers the determination of the breaking load and calculated flexural strength of a rectangular cross section of a preformed block-type thermal insulation tested as a simple beam.
2504
[Page extract]
*corp Mastercard CQM: ID-1
Mastercard CQM requirement covers Peel Strength Test (TM-412 #8120#) and Advanced Peel Strength Test (TN-424 #8240#). Methods are based around ISO 10373-1 to determine the peel strength between 2 layers of an ID or security card.
2505
[Page extract]
ASTM D7264 / D7264M-15
ASTM D7264 is a test method used to determine the flexural stiffness and strength properties of polymer matrix composites. The test method summarises two procedures:
2506
[Page extract]
ASTM F1304-18
ASTM F1304 is a test method used to determine the deflection of relatively rigid resilient floor tile such as vinyl composition tile and resilient flooring with a rigid polymeric core.
2507
[Page extract]
BS EN ISO 71-2
BS EN 71-2 covers the flammable materials which are prohibited in all toys and the requirements concerning flammability of certain toys when exposed to fire.
2508
[Page extract]
ASTM C1028
This test method covers the measurement of static coefficient of friction of ceramic tile or other surfaces under both wet and dry conditions while utilizing Neolite heel assemblies. This test method can be used in the laboratory or in the field.
2509
[Page extract]
ISO 2555
Specification of a method for determining an apparent viscosity of resins in a liquid state, using one of the types of rotational viskosimeter described in this standard.
2510
[Page extract]
ISO 7622-1
ISO 7622-1 specifies a method for the determination of the elongation of steel cords constituting the carcass of conveyor belts, when subjected to a force corresponding to 10 % and 60 % of the specified tensile strength.
2511
[Page extract]
TAPPI T 556
This procedure is used to measure the bending resistance of paper and paperboard in the machine and cross machine directions, by determining the bending resistance in mN of a 38mm (1.5in) wide vertically clamped sample, at 15o or 7.5o deflection.
2512
[Page extract]
BS 6319-7
BS 6319-7 is a test method for determining the tensile strength of resin and polymer/cement compositions for use in construction.
2513
[Page extract]
BS EN 1465
Specifies a method for determining the tensile lap-shear strength of bonded assemblies when tested on a standard specimen and under specified conditions of preparation and testing.
2514
[Page extract]
BS EN ISO 10619-1
BS EN ISO 10619-1 is a test method covering bending tests on rubber or plastics hoses and tubing.
2515
[Page extract]
*corp 01M-01-309
To determine the elongation and recovery properties of elastic Tapes (Both Woven and Knitted), reflectives, elastic tie cords Decorative TPU Bonding and Bonding Tape.
2516
[Page extract]
ASTM D6241-04
This test method for determining the puncture strength of geotextiles is to be used by the industry as an index of puncture strength.
2517
[Page extract]
ASTM E2658-15
These practices cover procedures and requirements for the calibration and verification of testing machine speed by means of standards calibration devices
2518
[Page extract]
ASTM D4541-09e1
This test method uses a class of apparatus known as portable pull-off adhesion testers. They are capable of applying a concentric load and counter load to a single surface so that coatings can be tested even though only one side is accessible.
2519
[Page extract]
ISBT PTC-00002
This ISBT (International Society of Beverage Technologists) publication outlines dimensional and physical characterization and performance test methods for PET beverage bottles for use in CSD (Carbonated Soft Drink), Hotfill, and Cold Fill applications.
2520
[Page extract]
ASTM D1004
ASTM D1004-13 covers the determination of tear strength or tear resistance of flexible plastic film and sheeting. The site of tear is initiated by a high stress concentration caused by the 90° angle in the specimen.
2521
[Page extract]
ASTM C480
This test method covers the determination of the creep characteristics and creep rate of flat sandwich constructions loaded in flexure, at any desired temperature.
2522
[Page extract]
ASTM D3472
This test method covers the measurement of the torque developed when Type IA child-resistant closures are rotated in the counter-clockwise direction.
2523
[Page extract]
ISO 11502
Describes a qualitative and a quantitative method for assessing the tendency of flexible plastics films and sheets to adhere to one another when left in contact for some time, at a specified temperature and under light pressure.
2524
[Page extract]
BS 6319-6
BS 6319-6 is a test method for determining the modulus of elasticity in compression of resin and polymer/cement compositions for use in construction.
2525
Software
TTT_Certify
TTT_Certify softwareGenerate compliant torque calibration certificates
Included with the TTT-300 is our TTT_Certify software for generating calibration certificates, conforming to ISO 17025 standards for handheld, indicating and click torque tools, such…