Search results
2276
[Page extract]
ISO 4674-1
Describes two methods for determining the forces necessary to initiate and propagate tearing of a coated fabric using the constant rate of tear method. The methods described are:
method A: tongue tear
method B: trouser tear
2277
[Page extract]
ISO 11897
ISO 11897 specifies a method for the determination, under given conditions, of the resistance to tear propagation on an edge fold of sacks made from thermoplastic flexible film.
2278
Case study
Peel testing Ostomy bags
Requirement
Salts Healthcare, a leading manufacturer and supplier of health care products required a low capacity system for testing the integrity of their hydrocolloid products.
2279
[Page extract]
ASTM D3106
This test method covers the determination of the permanent deformation of bare, continuous elastomeric monofilaments and filament yarns made from rubber, spandex, anidex, or other elastomers subjected to prolonged periods of tension.
2280
[Page extract]
ISO 1926
ISO 1926 specifies a method of determining the behaviour of rigid cellular plastics materials when they are subjected to a tensile stress.
2281
[Page extract]
ASTM D3480
These test methods cover the measurement of the downward force required to open or activate child-resistant snap-engagement packages.
2282
[Page extract]
ISO 527-4
ISO 527-4 determines the tensile properties of isotropic and orthotropic fibre reinforced plastic composite sheeting and film including the tensile strength and modulus of elasticity, strain, elongation and the tensile energy to break (TEB).
2283
Event
Essentials of Cork Pull & Cork Elasticity Testing
Cork stoppers are extremely successful wine bottle closures that have been in use from ancient times.
2284
[Page extract]
ISO 8067
ISO 8067 specifies two methods for the determination of the tear strength of flexible cellular polymeric materials:
Method A, using a trouser test piece
Method B, using an angle test piece without a nick
2285
[Page extract]
ASTM D5528-13
ASTM D5528 is a test method, which determines the opening Mode I interlaminar fracture toughness of continuous fiber-reinforced composite materials. It uses a a double cantilever beam (DCB) specimen. Susceptibility to delamination is one of the major
2286
[Page extract]
ASTM D1975
ASTM D1975 provides procedures for an indication of the environmental stress crack resistance of plastic injection moulded open head pails, covers, and components as a summation of the effects of container design, resin and manufacturing.
2287
[Page extract]
TAPPI T 818
The ring crush test correlates with edgewise compression strength of paperboard. This method is intended for paperbaord between 0.28mm (0.011 in.) and 0.51mm (0.020 in) thick.
2288
[Page extract]
ASTM D6641 / D6641M - 16e1
The ASTM D6641 test method determines compressive properties of polymer composite materials by applying combined end-loading and shear-loading using a combined loading compression (CLC) fixture.
2289
[Page extract]
ASTM D3354
ASTM D3354 is a test method that provides quantitative information on the degree of blocking i.e. unwanted adhesion between layers of plastic film.
2290
[Page extract]
BS EN 2597
BS EN 2597 is test method covering tensile testing on carbon fibre reinforced plastics.
Before conducting BS EN 2597, it is important to read the entire specification. Standards can be obtained from appropriate standard authorities.
2291
[Page extract]
ASTM E328-02
These test methods cover the determination of the time dependence of stress (stress relaxation) in materials and structures under conditions of approximately constant constraint, constant environment, and negligible vibration.
2292
[Page extract]
BS EN ISO 6259-1
BS EN ISO 6259-1 is a test method for determining the tensile properties of thermoplastic pipes.
2293
[Page extract]
ASTM D4027-98
This test method describes equipment and procedures to measure the shear modulus and shear strength of adhesive layers between rigid adherends.
2294
[Page extract]
*corp 01M-01-309
To determine the elongation and recovery properties of elastic Tapes (Both Woven and Knitted), reflectives, elastic tie cords Decorative TPU Bonding and Bonding Tape.
2295
[Page extract]
BS EN ISO 2060
Cancels and replaces the first edition (1972). Specifies a method for the determination of the linear density of all types of yarn in package form. Includes seven optional procedures based on different methods of conditioning and preparation.
2296
[Page extract]
BS EN 1608
This European Standard specifies the equipment and procedures for determining the tensile strength of a product parallel to its faces. It is applicable to thermal insulating products.
2297
[Page extract]
BS EN 1271
Balls (sports equipment), Ball-games equipment, Sports nets, Dimensions, Design, Classification systems, Performance, Breaking load, Yarn, Cords, Grades (quality), Safety measures, Mechanical testing, Instructions for use, Marking, Foundations, Anchorag
2298
[Page extract]
BS 1726-1
Provides guidance on methods of specifying and tolerancing hot coiled compression springs, and cold coiled springs that fall outside the size range limits specified in BS EN 15800.
2299
[Page extract]
BS EN 1464
Specifies a floating roller method for the determination of the peel resistance of adhesive bonds between one rigid adherend and one flexible adherend when tested under specified conditions of preparation and testing.
2300
[Page extract]
ASTM D2918
This test method provides data for assessing the durabilities of adhesive joints by means of T-peel type specimens stressed in contact with air, air in equilibrium with certain solutions, water, aqueous solutions, or other environments at various temper