Search results
951
Accessory
Rubber jaws for Mec227 Lightweight Vice Grip, 250 N, 10 x 25mm
Mec227-BG25
Rubber-faced Jaws (10mm x 25mm) - nickel-plated having 1mm thick layer of nitrile rubber coating.
Opening span = 0 - 6mm.
For fragile samples, which may get weakened by pinching at the contact-edge of the grip. (e.g. thin films, filaments, fibres and…
952
Accessory
Diamond coated jaws for Lightweight Pneumatic Plane Grip, 200 N, 25 x 25 mm
Mec94-BD25
Diamond Jaws (25mm high x 25mm wide) - nickel-plated having clamping surface coated with synthetic diamonds.
Opening span = 0 - 20 mm.
For materials which need a “bite” to secure a good grip (e.g. soft metals {aluminium, copper, soft steel, paper and…
953
[Page extract]
Power your torque testing
Sophisticated power - easy to use
Looking for an automated torque testing system to improve the accuracy and repeatability of your measurements compared to manual torque testers?
954
[Page extract]
Plastic components and sub-assemblies
The successful design and production of plastic components requires careful attention to be paid to many elements. The choice of plastic material depends on the desired performance characteristics - will parts be under constant load?
955
[Page extract]
ASTM E1012-12e1
It has been shown that bending stresses that inadvertently occur due to misalignment between the applied force and the specimen axes during the application of tensile and compressive forces can affect the test results.
956
Event
Webinar: Adhesion/Peel strength testing
There is a reason people reach for duct tape as a fix for almost everything – adhesion strength.
From busted pipes to ripped furniture, the preference for a solution that “does not easily peel off” is the guiding principle for manufacturers.
957
[Page extract]
PD CEN/TR 17394-1
This document provides requirements for security of attachment for clothing components of infant clothing.
958
Case study
End float test of inhaler cap
Requirement
'End float is the displacement in mm of a product', in this case the dispensing cap closure of the inhaler measured at a specific load.
959
Case study
Luer lock fastening and release torque
Customised engineering example
Luer lock test standards frequently call for measuring torque whilst simultaneously applying a pre-defined axial force.
960
Case study
Card and paper crease line testing
Customised engineering example
A packaging production company needed to test the crease force of the ink-coated card used in their fully-enclosed cartons.
961
[Page extract]
BS 7548
Describes requirements and test methods for sterile syringes
with or without needles for single use solely for the injection
of insulin in humans. Covers syringes for use with 40 units of
962
Case study
Tensile testing on polyethylene film
Requirement
Eurofilm Mantzaris S.A. are a leading producer of polyethylene films used for packaging and agricultural applications.
963
[Page extract]
ASTM D953-18
ASTM D953 is a test method that covers the determination of the pin-bearing strength of rigid plastics in either sheet form, molded form, or in reinforced thermoset form.
964
[Page extract]
ISO 4049
This document specifies requirements for dental polymer-based restorative materials supplied in a form suitable for mechanical mixing, hand-mixing, or intra-oral and extra-oral external energy activation, and intended for use primarily for the direct or
966
[Page extract]
BS ISO 3597-2
ISO 3597-2 specifies a method for determining the flexural strength of composite rods of circular cross-section made of roving-reinforced resin.
967
Case study
90 degree peel test filter paper
Customised engineering example
Floating roller peel jigs are regularly used for testing laminates where the backing sheet is rigid and the facing sheet is flexible (e.g. security cards)
968
[Page extract]
Mecmesin solutions for equibiaxial flexure testing
Mecmesin designs and manufactures precision equipment for standards-compliant equibiaxial flexure compression testing, including the concentric ring method. Our systems combine robust mechanical design with advanced control and analysis software.
969
Case study
Bulk liquid carrier closures
Customised engineering example
Our client manufactures liquid bulk carriers fitted with two-part plastic valve closures. The collar is welded to a plastic bag, and the valve closure is fixed onto it by a compression joint.
970
Case study
Tamper-Proof Closure Test
Requirement
Alcoa required a system to quickly test the tamper-proof rings on soft drink and mineral water closures.
The system had to be easy to operate and allow caps to be loaded quickly.
971
[Page extract]
Why choose Mecmesin for floating roller peel testing
With decades of experience in materials and force measurement, Mecmesin offers robust and configurable systems that meet industry test standards while adapting to application-specific needs.
972
Case study
Torque tester for windows and sunroof controls
Requirement
The customer requested a portable system which would quickly and easily allow him to test the torque required to open and close windows in a car.
973
Case study
Toy testing to attachment strength safety standards
Requirement
The customer supplies plush giftware to retailers such as Clintons. Their plush products are manufactured to European toy safety standard BS EN 71-1:1998 (Safety of toys - Part 1: Mechanical and physical properties).
974
[Page extract]
Torque systems
Do you need a level of accuracy and repeatability which just cannot be achieved by manual testers? Do you want to reduce testing time and increase throughput for operators when performing batch tests?
975
[Page extract]
ASTM F36-15
The ASTM F36 test method covers the determination of the short-time compressibility and recovery at room temperature of sheet-gasket materials, form-in-place gaskets, and in certain cases, gaskets cut from sheets.