Search results
876
[Page extract]
BS ISO 3597-2
ISO 3597-2 specifies a method for determining the flexural strength of composite rods of circular cross-section made of roving-reinforced resin.
877
Event
Live Demonstration: Wire Crimp Tensile Testing
Wire crimp tensile testing provides confidence in the integrity and performance of crimped connections, ensuring reliability, safety, and compliance with industry standards.
878
[Page extract]
MIL AS23190A
AS23190 is a procurement specification that covers a series of plastic and metal components and devices used for the tying, positioning, and supporting cable, cable assemblies, wire, and wire bundles in electrical, electronic and communication equipment
879
[Page extract]
ASTM D6272-17
This test method covers the determination of flexural properties of unreinforced and reinforced plastics, including high-modulus composites and electrical insulating materials in the form of rectangular bars molded directly or cut from sheets, plates, o
880
[Page extract]
EN 12089
Thermal insulating materials, Bend testing, Construction materials, Loading, Deflection tests, Mechanical testing, Testing conditions, Test equipment, Test specimens, Reports, Accuracy, Reproducibility.
881
[Page extract]
ASTM D3822
This test method covers the measurement of tensile properties of natural and man-made single textile fibers of sufficient length to permit mounting test specimens in a tensile testing machine.
882
[Page extract]
Motorised torque test stands
Repeatable torque testing
Looking for a motorised torque testing system to improve the accuracy and repeatability of your measurements compared to manual torque testers?
883
[Page extract]
BS EN ISO 8295
ISO 8295 specifies a method for determining the coefficients of starting and sliding friction of plastics film and sheeting when sliding over the same or other substances. It is intended to be used for non-sticky plastic film and sheeting of up to appr
884
Case study
Glued cardboard packaging integrity
Requirement
Graphic Packaging International is a leading designer and manufacturer of food and beverage packaging.
885
[Page extract]
ASTM D3167
ASTM D3167 is used to determine the average peel strength or force of an adhesive and bonding agents through the use of floating roller fixtures. This is used to compare adhesives or to compare adhesive surface preparation procedures.
886
Case study
Tensile testing on polyethylene film
Requirement
Eurofilm Mantzaris S.A. are a leading producer of polyethylene films used for packaging and agricultural applications.
887
[Page extract]
BS 1726-1
Provides guidance on methods of specifying and tolerancing hot coiled compression springs, and cold coiled springs that fall outside the size range limits specified in BS EN 15800.
888
[Page extract]
ISO 13955
ISO 13955 is used to assess the cohesion of a PE pipe/electrofusion socket or saddle assembly. Applicable to pipes with a nominal outside diameter between 16 mm and 225 mm
889
Event
Materials Testing: Theory and Practice Pt. 2
Materials testing is often the last step in the manufacturing process. Yet, quality is the result of both the process and the material. If the material that goes into the product is inadequate or defective, then the product may be deficient or faulty.
890
[Page extract]
ISO 252
ISO 252 specifies two test methods, A and B, for determining the adhesion strength between constitutive elements of a conveyor belt, i.e. between plies and between covers and carcass.
891
Event
Cap Closure and Removal Torque Testing
The primary objective for measuring and analyzing the torque characteristics of a container cap is to accurately determine not only the quality of the part or process, but also the root cause of a wide variety of defects.
892
[Page extract]
BS EN 12209
BS EN 12209:2016 specifies requirements and test methods for the durability, strength, security, and function of mechanically operated locks and latches and their locking plates for use in doors, window doors and entrance doors in buildings.
893
[Page extract]
ISO 814
ISO 814 specifies a method for determining the adhesion strength of rubber-to-metal bonds where the rubber part is assembled between two parallel metal plates, using the adhesive system under investigation
894
[Page extract]
Digital force gauges
Mecmesin's digital force gauges deliver outstanding accuracy and affordability.
895
[Page extract]
BS 6319-7
BS 6319-7 is a test method for determining the tensile strength of resin and polymer/cement compositions for use in construction.
896
[Page extract]
ISO 17454
ISO 17454 specifies a method for testing the adhesion between layers of multilayer pipes using a pulling test rig.
897
[Page extract]
BS EN 12814-7
BS EN 12814-7 is a tensile test method with waisted test specimens for testing welded joints of thermoplastics semi-finished products.
898
[Page extract]
SAE J1701M
This SAE Information Report is provided as an advisory guide. Individual application discretion is recommended. The content has been presented as accurately as possible, but responsibility for its application lies with the user.
899
[Page extract]
BS EN ISO 10619-1
BS EN ISO 10619-1 is a test method covering bending tests on rubber or plastics hoses and tubing.
900
Case study
Rotary damper gear precision torque characteristics
Requirement
A global manufacturer and distributor of component parts that are used in products across many industries including transport, beauty, consumer goods and healthcare, came to Mecmesin with a challenging torque measurement applicatio